background image

 

Cleaning and Maintenance 

36 / 40   

 

 

 

116622 

EN 

Appliance Door/Internal Glass Pane 

 

 

Double glazing facilitates cleaning. The 
internal glass pan may be opened and 
removed when required. 

1.  To this end, rotate clockwise both latches 

(top and bottom) that hold the internal 
glass pane in place (Fig. 18). 

2.  Tilt the internal glass pane (Fig. 19). 

3.  Clean both sides of internal glass pane 

and appliance door with the use of 
appropriate agents. 

ATTENTION! 
Do not use any aggressive and abrasive 
cleaning agents. 

 
4.  Thoroughly dry the internal glass pane 

from both sides. 

5.  Again, close the internal glass pane or re-

insert it correctly, and lock latches in their 
initial positions by turning them counter-
clockwise.  

Fig. 18 

 

 

Fig. 19 

 
 

Control Panel Ventilation Filter 

 

 

Clean the control panel ventilation filter at 
least once a month. 

1.  Pull the ventilation filter from its holder 

by holding it with your fingers (Fig. 20). 

2.  Clean the ventilation filter manually with 

use of water and soap. Rinse with fresh 
water and then leave it to dry. 

It is recommended to replace the ventilation 
filter at least once a year or even more 
frequently if the appliance is operated in 
environments featuring high concentration 
of flours or similar substances. 

Fig. 20 

 

Содержание 116622









































Отзывы: