Bartington Magmeter-2 Скачать руководство пользователя страница 17

Страница: 17 / 20

BARTINGTON INSTRUMENTS

Page 17 of 20 OM2448/4

Magmeter-2 stuck
in Balanced or
Unbalanced mode

Defective component

Contact Bartington service team regarding

repair

One or both LEDs do

not light correctly

Defective component

Contact Bartington service team regarding

repair

Backlight does not
illuminate the screen

Button not pressed and

held

Press and hold button to maintain backlight

Magmeter-2 defective

Contact Bartington service team regarding

repair

With a sensor
connected, all output

signals are faulty

Coupled incorrectly

Check position of AC/DC coupling switch

Balance mode set

incorrectly

Check position of balanced/unbalanced

mode switch

Defective sensor cable

Check sensor cable using relevant datasheet.

If found to be defective, contact Bartington

service team regarding repair

Sensor defective

Contact Bartington service team regarding

repair

Magmeter-2 defective

Contact Bartington service team regarding

repair

With a sensor
connected, one or
two output signals are

faulty

Defective sensor cable

Check sensor cable using relevant datasheet.

If found to be defective, contact Bartington

service team regarding repair

Sensor defective

Contact Bartington service team regarding

repair

Magmeter-2 defective

Contact Bartington service team regarding

repair

No output displayed

(when not mains
connected via the plug-
in charger adaptor)

Batteries flat

Recharge the batteries

Batteries expired

Replace batteries and charge

Batteries not fitted

Fit batteries and charge

None of the above

Contact Bartington service team regarding

repair

Содержание Magmeter-2





















Результаты поиска

Содержание Magmeter-2

Отзывы:

Похожие инструкции для Magmeter-2

Бренды по названию

Популярные бренды

Bartington Magmeter-2, Руководство по эксплуатации

Результаты поиска

Содержание Magmeter-2

Отзывы:

Похожие инструкции для Magmeter-2

Бренды по названию

Популярные бренды