Bartell BXR836, Руководство пользователя и каталог запасных частей

Страница: 12 / 33

375 ANNAGEM BLVD., MISSISSAUGA, ONTARIO, CANADA, L5T 3A7, 905-364-4200 FAX 905-364-4201
200 COMMERCE DRIVE, FREEHOLD, NEW JERSEY, USA, 07728, 732-566-6400 FAX 732-566-5444
CREATED: 07/04
REVISED: 06/14
BXR836 RIDE-ON TROWEL INSTRUCTION MANUAL
BARTELL MORRISON INC. BARTELL MORRISON (USA) LLC
375 ANNAGEM BLVD. – MISSISSAUGA – ONTARIO – CANADA – L5T 3A7 – 866-501-1683 – FAX 905-364-4200
25 INDUSTRIAL DR. – KEYPORT – NEW JERSEY – USA – 07735 – 888-999-1570 – FAX 732-566-5444
Created: 05/2012
Revised: 00
Revised: 05/2012
12
TROWEL ARM ADJUSTMENT FIXTURE
PART #20801
Unit 36” (TS88)
1) 10411 – Trowel arm
2) 10817 – Lift lever
3) 10808 – Jam nut
4) 10809 – Set screw
5) 10824 – Block top
6) 10507 – Bolt
7) 10816 – Jam nut
8) 10815 – Carriage bolt
9) 10832 – Adjustment bar
10) 10507 – Bolt
Figure
The trowel arm adjustment fixture (20801) is reversible.
By rotating the arm clamping fixture and the ring bolt,
both left hand and right hand trowel arms may be
adjusted. Before attempting adjustment, determine
whether the trowel arm is right handed or left handed.
When adjusting left hand trowel arms use the side of the
fixture marked “L”. When adjusting right hand trowels
arms use the opposite side. The adjustment bar will be
set on “46” for the BXR836 trowel arm.
ADJUSTMENT PROCEDURE
1. Remove all trowel arm assemblies (1 & 2 arm and
attached lift lever) from suspected maladjusted spider
plate.
2. Remove lift lever (2) from trowel arm (1) by first
loosening jam nut (3) then square head screw (4). If
upon inspection (method left to discretion of
serviceman) any trowel arm (1) is found to be in a
bent condition, it must either be brought back to its
original straight condition (method left to the
serviceman’s discretion) or replaced with new part.
3. Replace lift levers (2) on new or straightened arms
(1) by reversing procedure described above.
NOTE: IT IS IMPORTANT THAT WHEN TIGHT-
ENING SQUARE HEAD SETSCREW (4), IT SEATS
ITSELF SECURELY INTO DIMPLE MACHINED IN
ARM.
4. Place trowel arm assembly (1 and 2) in fixture (5)
with lift lever (2) butting up against fixture. Secure in
place with bolts (6).
5a.
5. Loosen locknut (7) and screw carriage bold (8) down
to full depth allowable. This will provide for ample
clearance to swing adjustment bar (9) over head of
carriage bolt. Adjustment bar (9) is stamped for
appropriate size of machine. Swing appropriate side
directly over carriage bolt (8) and secure in place with
bolt (10).
6. Adjust carriage bolt (8) upwards until contact is made
with adjustment bar (9); holding carriage bolt in
position with one wrench, tighten locknut (7) to secure
in position with second wrench.
NOTE: IT IS VITALLY IMPORTANT TO ENSURE
THAT ONCE THE CARRIAGE BOLT IS ADJUSTED
TO THE CORRECT HEIGHT, IT DOES NOT MOVE
BEFORE, OR DURING THE TIGHTENING OF
LOCKNUT.
7. This same procedure is to be followed with ALL arms
from spider plate assembly, and will ensure correct
and exact adjustment.
TROWEL ARM ADJUSTMENT SCREW
When assembling trowel blades to trowel arms, the
adjustment screw should NEVER protrude below the
under-side surface to a trowel arm except when using for
emergency on-site adjustment to level trowel blades.
If the adjustment screw is not flush with the underside of
the trowel arm, then this will cause the power trowel to
bounce and vibrate especially at high speed. This will
also cause the trowel blades to leave an uneven finish on
the concrete due to the blades not being level to one
another.
Make certain that the adjusting screw is held firmly in
place while tightening the bolt which secures the blade to
the trowel arm.
12