background image

6

7

4. After opening the safe, reinstall the keypad cover and screw down the cover with 

    the housing.

CHANGING THE MASTER CODE (Code length: 3-8 digits)

NOTE: Always perform this operation with the door opened. Test new code a couple 

of times before closing the door.

 

Safe retains 1 master code

1. Press 

“ * * “

 and 2 short beeps will be heard

2. Press 

“8 8 8 #”

 and 2 short beeps will be heard

3. Input 

“Current Master Code #”

 and 2 short beeps will be heard(For 1st time to 

    use, Current Master Code is Factory default code is:1-2-3-4-5-6-7-8)

4. Input 

“New Master Code #”

 and 2 short beeps will be heard

5. Re-Input 

“New Master Code #”

 and 2 short beeps will be heard, light stays green 

    for 3 seconds

 Example:

 

** 888 # Current Master Code # New Master Code # New Master Code #

 

If the master code didn’t save successfully, the lock will beep 5 times. The  

 

old code is still valid. Please repeat steps 1-5.

REGISTER USER CODES (Code length: 3-8 digits)

Safe retains 5 user codes

1. Press “ * * “ and 2 short beeps will be heard 

2. Press “3 3 3 #” and 2 short beeps will be heard 

3. Input “Current Master Code #” and 2 short beeps will be heard 

4. Input “User No. #”( User No.: Specify which user you would like to register,

    1,2,3,4 or 5) and 1 short beep will be heard

5. Input “New User Code #” and 2 short beeps will be heard

6. Re-Input “New User Code #” and 2 short beeps will be heard, light stays green for 

    3 seconds

CHANGE USER CODES

1. Press “ * * “ and 2 short beeps will be heard 

2. Press “4 4 4 #” and 2 short beeps will be heard

3. Input “Current User Code #” and 2 short beeps will be heard

4. Input “User No. #” ( User No.: Enter the User No. that identifies the Current User 

Code on Step 3) and 1 short beep will be heard

5. Input “New User Code #” and 2 short beeps will be heard

6. Re-Input “New User Code #” and 2 short beeps will be heard

DELETE USER CODES

1. Press “ * * “ and 2 short beeps will be heard 

2. Press “666 #“ and 2 short beeps will be heard 

3. Input “ Current Master Code# “ and 2 short beeps will be heard

4. Input “User No.#” and 1 short beep will be heard

5. Input “User No.#” and 2 short beeps will be heard

If the user code didn’t delete successfully, the lock will beep 5 times. Please

repeat steps.

SETTING SINGLE USER & DUAL USER MODES

Single User Mode

This mode will require enter Only ONE valid user code to open the safe

1. Press “ * * “ and 2 short beeps will be heard 

2. Press “158 # “ and 2 short beeps will be heard 

3. Input “ Current Master Code# ” and 2 short beeps will be heard

4. Press “ 1# “and 2 short beeps will be heard

This Operation will set the safe to single user mode, please test after set up.

If the Single User Mode didn’t set successfully, the lock will beep 5 times. Please 

repeat steps.

Dual User Mode 

This mode will require enter any TWO valid user codes to open the safe. 

Note: Master code doesn’t require another code to open safe under Dual User 

mode. 

Содержание AX13308







Отзывы: