background image

Wall/Ceiling Mount - Back Power Feed

1. Insert a flat blade screwdriver into the two slots to remove the front 

cover from the backplate. (Fig. 1)

2. Remove from the backplate the center knockout and any knockouts 

that are needed to mount to the J-box.

3. Route wires through the center hole of the backplate, then mount the 

backplate to the J-box. (Fig. 2)

4. Make electrical connections; see 

Electrical Connections

 section.

5. Connect the remote lamp wires if the fixture is remote capable. Refer 

to 

Remote Lamp Connection

 section.

6. Plug the male battery connector into the female battery connector on 

the PCBA. 

7. Snap the front cover back onto the backplate.

8. Restore power and test the fixture by pressing the test button. The 

LED heads will turn on.

9. Adjust the direction of the lamp heads for optimal lighting coverage. 

(Fig. 3)

Wall/Ceiling Mount - Top Power Feed

1. Insert a flat blade screwdriver into the two slots to remove the front 

cover from the backplate. (Fig. 1) 

2. Remove appropriate knockouts from backplate and mount to wall.

3. Remove the top knockout on the top flange of the fixture for the 

flexible conduit access hole. (Fig. 4)

4. Secure conduit (or surface raceway) to the top hole and feed wires.

5. Make electrical connections; see 

Electrical Connections

 section.

6. Connect remote lamp wires if the fixture is remote capable. Refer to 

Remote Lamp Connection

 section.

7. Plug the male battery connector into the female battery connector on 

the PCBA.

8. Snap the front cover back onto the backplate.

9. Restore power and test the fixture by pressing the test button. The 

LED heads will turn on.

10. Adjust the direction of the lamp heads for optimal lighting coverage.

Max. Mounting Height

LED-51: 15ft

LED-52: 26ft

Fig. 1

Fig. 2 - Back Power Feed 

Fig. 3

Fig. 4 - Top Power Feed

Battery

Connector

Front 

Cover

Backplate

Remote 

Connector

Wire Nuts

Lamp 

Head

Battery 

Connector

Remote 

Connector

Conduit

Front Cover 

Knockout

Wire 

Nuts

10070204 

R

EV 5 - 05/22

2

800-533-3948 www.barronltg.com

LED-51/52 Series

Installation Instructions

Содержание EXITRONIX LED-51 Series

Страница 1: ...er cords touch hot surfaces Equipment should be mounted in locations and at heights where it will not be readily subjected to tampering by unauthorized personnel The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition Any modification or use of non original components will void the warranty and product liability Do not use this equipment for other than inte...

Страница 2: ...lots to remove the front cover from the backplate Fig 1 2 Remove appropriate knockouts from backplate and mount to wall 3 Remove the top knockout on the top flange of the fixture for the flexible conduit access hole Fig 4 4 Secure conduit or surface raceway to the top hole and feed wires 5 Make electrical connections see Electrical Connections section 6 Connect remote lamp wires if the fixture is ...

Страница 3: ... on and the LED indicator light will turn off Release the test switch the LED indicator will turn on and the LED heads will turn off Troubleshooting Guide If the LED heads or the LED indicator do not illuminate check the following 1 Check AC supply verify that the unit has 24 hours AC supply 2 Check the battery connections 3 Discharge the battery and charge the battery for 24 hours or 48 hours for...

Страница 4: ...es whenever the Self diagnostic system has detected a fault condition Refer to the chart below to determine the fault condition Test Button Feature MANUAL TEST Pressing the test button will switch the unit into battery mode for a set amount of time The desired length of the test is determined by the number of times the test button is pressed Pressing the test button once will switch the unit into ...

Отзывы: