Barox LT-PIGE-804GBTME Series Скачать руководство пользователя страница 3

FCC Notice

 

This  equipment  has  been  tested  and  found  to  comply  with  the  limits  for  a  Class-A  digital  device, 
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against 
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio 
frequency energy. It may cause harmful interference to radio communications if the equipment is not 
installed  and  used  in  accordance  with  the  instructions.  However,  there  is  no  guarantee  that 
interference will not occur in a particular installation. If this equipment does cause harmful interference 
to  radio  or  television  reception,  which  can  be  determined  by  turning  the  equipment  off  and  on,  the 
user is encouraged to try to correct the interference by one or more of the following measures:

 

 

Reorient or relocate the receiving antenna.

 

 

Increase the separation between the equipment and receiver.

 

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected.

 

 

Consult the dealer or an experienced radio/TV technician for help.

 

 
 

Caution: Any changes or modifications not expressly approved by the grantee of this device could void 
the user's authority to operate the equipment.

 

 
 

CE Mark Warning

 

This is a Class-A product. In a domestic environment this product may cause radio interference in which 
case the user may be required to take adequate measures.

 

 
 

Industrial Ethernet Switches

 

Industrial Grade Gigabit Managed Ethernet Switches

 

 
 

User Manual

 

Version 1.0 (August 2015)

 

 
 

 
 

Содержание LT-PIGE-804GBTME Series
























Отзывы: