Baroness LM331 Скачать руководство пользователя страница 73

Страница: 73 / 103

Lubrication

About Lubrication

It is necessary to lubricate moving parts so that
they will not become stuck or damaged.
The locations where lubricant is used are
indicated in "Lubricating Points".
Apply the lubricant.

Lubricating Points

Apply lubricant at the following locations every
50 hours of operation.

8bq62b-485

Lubricating Points_001

Location

No. of

greasing

points

Steering cylinder spherical
bearing

Front mower cylinder spherical
bearing

Rear mower cylinder spherical
bearing

Steering cylinder spherical bearing
There are two locations.

8bq62b-487

Lubricating Points_002

Front mower cylinder spherical bearing
There are two locations.

8bq62b-488

Lubricating Points_003

8bq62b-489

Lubricating Points_004

Rear mower cylinder spherical bearing
There is one location.

8bq62b-490

Lubricating Points_005

Maintenance

LM331

Maintenance

Page 6-7

Lubrication

Содержание LM331








































































































Результаты поиска

Содержание LM331

Отзывы:

Baroness LM331, Руководство по эксплуатации для владельца, Страница: 73 / 103

Результаты поиска

Содержание LM331

Отзывы: