background image

5

Please note the following WARNINGS:

Warning

This warning is presented for compliance with California Proposition 65 and other regulatory
agencies and only applies to the insulation in this product. This product contains refractory
ceramic, refractory ceramic fiber or fiberglass insulation, which can produce respirable dust
or fibers during disassembly. Dust or fibers can cause irritation and can aggravate
preexisting respiratory diseases. Refractory ceramic and refractory ceramic fibers (after
reaching 1000

°

C) contain crystalline silica, which can cause lung damage (silicosis). The

International Agency for Research on Cancer (IARC) has classified refractory ceramic fiber
and fiberglass as possibly carcinogenic (Group 2B), and crystalline silica as carcinogenic to
humans (Group 1).

The insulating materials can be located in the door, the hearth collar, in the chamber of the
product or under the hot plate top. Tests performed by the manufacturer indicate that there
is no risk of exposure to dust or respirable fibers resulting from operation of this product
under normal conditions. However, there may be a risk of exposure to respirable dust or
fibers when repairing or maintaining the insulating materials, or when otherwise disturbing
them in a manner which causes release of dust or fibers. By using proper handling
procedures and protective equipment you can work safely with these insulating materials
and minimize any exposure. Refer to the appropriate Material Safety Data Sheets (MSDS)
for information regarding proper handling and recommended protective equipment. For
additional MSDS copies, or additional information concerning the handling of
refractory ceramic products, please contact the Customer Service Department at
Barnstead|Thermolyne Corporation at 1-800-553-0039.

S

AFETY

 I

NFORMATION

Warning
Refer servicing to qualified personnel.

Содержание HP18300





















Отзывы: