background image

Installing Particulate Filters

Two types of particulate filters are used in the
half-size canisters.

Prefilters  

These devices are string-wound filters designed
to prevent large particulates from entering a
water treatment system.

Final Filters  

These devices are pleated membrane filters
designed to remove particulates as small as 0.2
micron. These filters are supplied with gaskets
which are not used for B-pure installations.
Install filters as follows:

1.

Remove filter and adapters from
package.

2.

Remove canister from head by pressing
the thumb lever and rotating the ring 1/4
turn to the left.

3.

Lubricate the o-rings on the adapters
using pure water, then install adapters
into filters by turning the adapter as you
push it into the filter’s open end.

4.

Lubricate the o-rings on the head with
pure water, then secure the filter (includ-
ing adapter) onto the head by gently
pushing and turning the filter.

5.

Insert the canister vertically upward over
the filter and tighten 1/4 turn to the right.

12

I

NITIAL

O

PERATION

Warning
Depressurize system prior to
attempting to remove canisters.

Caution
Secure locking pin before oper-
ating; locking pin must be fully
released into hole on head
before the system is operated.

Содержание D4505

































Отзывы: