background image

2

Safety Information ..................................................................................................................................3  
Alert Signals ..........................................................................................................................................3 
Warnings ................................................................................................................................................3  
Introduction ............................................................................................................................................5 

Intended Use......................................................................................................................................5  
General Usage ..................................................................................................................................5  
Principles of Operation ......................................................................................................................5   

General Specifications for Furnaces ......................................................................................................6   

Environmental Conditions ..................................................................................................................6   

Declaration of Conformity ......................................................................................................................7  
Unpacking ..............................................................................................................................................8  
Installation ..............................................................................................................................................9  
Operation of Manual and Automatic Models ........................................................................................10  
Manual Control Models (F21124, F21125, F21120, F21120-33)..........................................................10   

Pyrometer ........................................................................................................................................10  

Operation All Modes Single Set Point Termperature Control (F21130, F21130-33, F21135) ..............11
Single Set Point Controller ..................................................................................................................12  
Single Ramp and Dwell........................................................................................................................16
Furnace Loading ..................................................................................................................................19 
Preventive Maintenance ......................................................................................................................20  

General Cleaning Instructions..........................................................................................................20  

Troubleshooting....................................................................................................................................21  
Maintenance and Servicing ..................................................................................................................24  

To Replace Vestibule End Caps ......................................................................................................24 
To Replace The Heating Element Tube (Without Case Assembly) ................................................24   
To Replace Pyrometer (Manual Control Models) ............................................................................25  
To Replace Manual Temperature Control Switch ............................................................................25  
To Replace Furnace Chamber ........................................................................................................26 
To Replace Type K (Chromel/Alumel) Thermocouple (Manual Control Models) ............................26
To Replace Type Platinel II Thermocouple (Single Set Point Control Models) ..............................27 

Replacement Parts List ........................................................................................................................29
Ordering Procedures ............................................................................................................................29
Wiring Diagrams ..................................................................................................................................30  
Warranty ..............................................................................................................................................32  

Table of Contents

Содержание 1260 Series

































Отзывы: