Barnes 3SEH-L Скачать руководство пользователя страница 3

3

Please Read This Before Installing Or Operating Pump. This 

information is provided for 

SAFETY and to PREVENT 

EQUIPMENT PROBLEMS

. To help recognize this information, 

observe the following symbols:

IMPORTANT!

 Warns about hazards that can result in 

personal injury or Indicates factors concerned with assembly, 

installation, operation, or maintenance which could result in 

damage to the machine or equipment if ignored.

CAUTION !

 Warns about hazards that can or will cause minor personal 

injury or property damage if ignored. Used with symbols below.

WARNING !

  Warns about hazards that can or will cause serious 

personal injury, death, or major property damage if ignored. Used with 

symbols below.

Only qualified personnel should install, operate and repair pump. Any 

wiring of pumps should be performed by a qualified electrician.  

WARNING ! -

 To reduce risk of electrical shock, pumps and 

control panels must be properly grounded in accordance with 

the National Electric Code (NEC) or the Canadian Electrical 

Code (CEC) and all applicable state, province, local codes and 

ordinances. 

WARNING! -

 To reduce risk of electrical shock, always 

disconnect the pump from the power source before handling 

or servicing. Lock out power and tag.

WARNING!

 Operation against a closed discharge 

valve will cause premature bearing and seal failure 

on any pump, and on end suction and self priming 

pump the heat build may cause the generation of 

steam with resulting dangerous pressures. It is 

recommended that a high case temperature switch 

or pressure relief valve be installed on the pump 

body.

CAUTION !

 Never operate a pump with a plug-in  type 

power cord without a ground fault  circuit interrupter.

CAUTION! 

Pumps build up heat and pressure 

during operation-allow time for pumps to cool 

before handling or servicing. 

WARNING!

 - 

DO NOT

 pump hazardous materials 

(flammable, caustic, etc.) unless the pump is specifically 

designed and designated to handle them.

Do not block or restrict discharge hose, as discharge hose 

may whip under pressure. 

WARNING! - DO NOT

 wear loose clothing that may 

become entangled in the impeller or other moving parts. 

WARNING! - 

Keep clear of suction and discharge openings. 

DO NOT

 insert fingers in pump with power connected.

Always wear eye protection when working on pumps.

Make sure lifting handles are securely fastened each time 

before lifting. 

DO NOT

 operate pump without safety devices 

in place. Always replace safety devices that have been 

removed during service or repair. Secure the pump in its 

operating position so it can not tip over, fall or slide.

DO NOT

 exceed manufacturers recommendation for 

maximum performance, as this could cause the motor to 

overheat.

DO NOT

 remove cord and strain relief. Do not connect 

conduit to pump.

WARNING!

 Cable should be protected at all times to avoid 

punctures, cut, bruises and abrasions - inspect frequently. 

Never handle connected power cords with wet hands.

WARNING!

 To reduce risk of electrical shock, all wiring 

and junction connections should be made per the NEC 

or CEC and applicable state or province and local codes. 

Requirements may vary depending on usage and location.

WARNING!

 Submersible Pumps are not approved for use in 

swimming pools, recreational water installations, decorative 

fountains or any installation where human contact with the 

pumped fluid is common.

WARNING! 

Products Returned Must Be Cleaned, Sanitized, 

Or Decontaminated As Necessary Prior To Shipment, To 

Insure That Employees Will Not Be Exposed To Health 

Hazards In Handling Said Material. All Applicable Laws And 

Regulations Shall Apply.

 

Bronze/brass and bronze/brass fitted pumps may contain 

lead levels higher than considered safe for potable water 

systems. Lead is known to cause cancer and birth defects or 

other reproductive harm. Various government agencies have 

determined that leaded copper alloys should not be used 

in potable water applications. For non-leaded copper alloy 

materials of construction, please contact factory. 

IMPORTANT! -

 Crane Pumps & Systems, Inc. is not 

responsible for losses, injury, or death resulting from a failure 

to observe these safety precautions, misuse or abuse of pumps 

or equipment.

SAFETY FIRST!

Hazardous fluids can 

cause fire or explo

-

sions, burnes or death 

could result.

Extremely hot - Severe 

burnes can occur on contact.

Biohazard can cause 

serious personal injury.

Hazardous fluids can Hazard

-

ous pressure, eruptions or ex

-

plosions could cause personal 

injury or property damage.

Rotating machinery

Amputation or severe 

laceration can result.

Hazardous voltage can 

shock, burn or cause death.

Содержание 3SEH-L






















Отзывы: