Bard LC6000-200 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 37

Bard LC6000-200 Скачать руководство пользователя страница 24

6. Press ENTER key to scroll to

Dehumidification Off

,

Passive On

or

Active On

(see Figure 24).

7. Press UP and DOWN keys to change

dehumidification setpoints to desired values.

FIGURE 24

Humidity Control Setpoints

FIGURE 26

Enabling Humidifier

FIGURE 25

Dehumidification Types

Humidification

If the humidity level is below 45% RH (Humidification
Setpoint), the LC will enable humidification for
that zone. Once the humidity level rises to 55%
RH (humidification setpoint plus 10% RH), the
humidification for that zone will be disabled.

NOTE:

Humidifiers are field supplied.

To change the humidification setpoint:
1. Press MENU key to go to the Main Menu screen.
2. Use UP or DOWN keys and ENTER key to enter

USER password 2000.

3. Press UP or DOWN keys to scroll to

Sys Config

;

press ENTER key.

4. Press UP or DOWN keys to scroll to

Zone 1

,

Zone 2

or

Zone 3

; press ENTER key.

5. Press UP or DOWN keys to scroll to

Setpoints A2-2

(Zone 1),

Setpoints A3-2

(Zone 2) or

Setpoints

A4-2

(Zone 3

)

.

6. Press ENTER key to scroll to

Humidification

(see

Figure 24).

7. Press UP and DOWN keys to change humidification

setpoint to desired value.

Enabling Humidifier

1. Press MENU key to go to the Main Menu screen.
2. Use UP or DOWN keys and ENTER key to enter

USER password 2000.

3. Press UP or DOWN keys to scroll to

Sys Config

;

press ENTER key.

4. Press UP or DOWN keys to scroll to

General

; press

ENTER key.

5. Press ENTER key to scroll to

Humidifiers

(see

Figure 26).

6. Press UP or DOWN keys to change value to

NONE

,

Zone 1

,

Z1 & Z2

or

Z1, Z2, & Z3

.

7. Press ENTER to scroll to

Humidifier Type

.

8. Press UP or DOWN keys to change value to

Relay

from

Comm

.

In addition to the setpoint configuration for
dehumidification, each zone must be configured for the
type of active dehumidification.
To change the dehumidification type:
1. Press MENU key to go to the Main Menu screen.
2. Use UP or DOWN keys and ENTER key to enter

USER password 2000.

3. Press UP or DOWN keys to scroll to

Sys Config

;

press ENTER key.

4. Press UP or DOWN keys to scroll to

Zone 1

,

Zone 2

or

Zone 3

; press ENTER key.

5. Press UP or DOWN keys to scroll to

Setpoints A2-3

(Zone 1),

Setpoints A3-3

(Zone 2) or

Setpoints

A4-3

(Zone 3

)

.

6. Press ENTER key to scroll to

Type

(see Figure 25).

7. Press UP and DOWN keys to change to desired

value. Dehumidification type choices are

None

,

Electric Reheat

,

Mechanical Reheat

or

Cycling

Reheat

. The units in the zone being configured will

need to have the capability of the setting being
selected (see unit model number).

Manual 2100-669F

Page

24 of 37

«
...
22
23
24
25
26
...
»

Содержание LC6000-200






































Отзывы:

Нет отзывов