background image

Manual 2100-695C 

Page 

43 of 56

This unit employs high-flow Coremax valves instead of 
the typical Schrader type valves.

WARNING! Do NOT use a Schrader valve core removal 

tool with these valves. Use of such a tool could result 

in eye injuries or refrigerant burns!

To change a Coremax valve without first removing the 
refrigerant, a special tool is required which can be 
obtained at www.fastestinc.com/en/SCCA07H. See the 
replacement parts manual for replacement core part 
numbers.

TABLE 12 

Cooling Pressures

Low side pressure ± 4 PSIG; High side pressure ± 10 PSIG

Tables are based upon rated CFM (airflow) across the evaporator coil. If there is any doubt as to correct operating charge being in the 
system, the charge should be removed and system evacuated and recharged to serial plate charge weight.

NOTE:

 

Pressure table based on high speed condenser fan operation. If condensing pressures appear elevated check condenser fan 

wiring. See “Condenser Fan Operation” on page 26.

Full Load Cooling

Air Temperature Entering Outdoor Coil °F

Model

Return Air Temp 

(DB/WB)

Pressure

75

80

85

90

95

100 105 110 115 120 125

WR35

75/62

Low Side

High Side

131
309

133
332

135
354

136
378

137
405

138
431

139
458

140
487

142
517

143
548

144
580

80/67

Low Side

High Side

140
317

142
340

144
363

145
388

147
415

148
442

149
470

150
499

152
530

153
562

154
595

85/72

Low Side

High Side

145
328

147
352

149
376

150
402

152
430

153
457

154
486

155
516

157
549

158
582

159
616

WR36

75/62

Low Side

High Side

130
290

131
312

132
334

134
359

135
384

136
411

137
439

138
468

139
498

140
530

142
564

80/67

Low Side

High Side

139
297

140
320

141
343

143
368

144
394

145
422

147
450

148
480

149
511

150
544

152
578

85/72

Low Side

High Side

144
307

145
331

146
355

148
381

149
408

150
437

152
466

153
497

154
529

155
563

157
598

WR58

75/62

Low Side

High Side

129
318

130
340

131
365

132
389

133
414

134
440

136
467

137
495

137
527

139
553

140
584

80/67

Low Side

High Side

138
326

139
349

140
374

141
399

142
425

143
451

145
479

146
508

147
537

149
567

150
599

85/72

Low Side

High Side

143
337

144
361

145
387

146
413

147
440

148
467

150
496

151
526

152
556

154
587

155
620

Part Load Cooling

Air Temperature Entering Outdoor Coil °F

Model

Return Air Temp 

(DB/WB)

Pressure

75

80

85

90

95

100 105 110 115 120 125

WR35

75/62

Low Side

High Side

137
282

137
303

137
326

138
348

139
372

140
397

141
422

143
449

144
476

146
504

148
533

80/67

Low Side

High Side

146
289

147
311

147
334

148
357

149
382

150
407

151
433

153
460

154
488

156
517

158
547

85/72

Low Side

High Side

151
299

152
322

152
346

153
369

154
395

155
421

156
448

158
476

159
505

161
535

164
566

WR36

75/62

Low Side

High Side

119
268

125
288

131
308

136
331

140
354

143
378

146
405

148
432

149
460

150
490

149
522

80/67

Low Side

High Side

127
275

134
295

140
316

145
339

150
363

153
388

156
415

158
443

159
472

160
503

159
535

85/72

Low Side

High Side

131
285

139
305

145
327

150
351

155
376

158
402

161
430

164
459

165
489

166
521

165
554

WR58

75/62

Low Side

High Side

135
283

136
304

136
327

137
350

137
375

138
402

138
428

140
456

141
486

142
416

143
547

80/67

Low Side

High Side

144
290

145
312

145
335

146
359

147
385

148
412

148
439

150
468

151
498

152
529

153
561

85/72

Low Side

High Side

149
300

150
323

150
347

151
372

152
398

153
426

154
454

155
484

156
515

157
548

158
581

Содержание FUSION-TEC WR36BPB

























































Отзывы: