RLS W12 02/12/2014
2
Users definition
Throughout this manual, the term SERVICE PERSONNEL refers to persons having appropriate technical training and experience
necessary to be knowledgeable of potential hazards to which they are exposed (including, but not limited to HIGH VOLTAGE
ELECTRIC and ELECTRONIC CIRCUITRY and HIGH BRIGHTNESS PROJECTORS) in performing a task, and of measures to minimize
the potential risk to themselves or other persons. The term USER and OPERATOR refers to any person other than SERVICE
PERSONNEL, AUTHORIZED to operate professional projection systems.
A RLS W12 projector is intended "FOR PROFESSIONAL USE ONLY" by AUTHORIZED PERSONNEL familiar with potential hazards
associated with high voltage, high intensity light beams, ultraviolet exposure and high temperatures generated by the lamp
and associated circuits. Only qualified SERVICE PERSONNEL, knowledgeable of such risks, are allowed to perform service
functions inside the product enclosure.
1.2 Important safety instructions
To prevent the risk of electrical shock
•
This product should be operated from a mono phase AC power source.
•
This apparatus must be grounded (earthed) via the supplied 3 conductor AC power cable. If none of the supplied power
cables are the correct one, consult your dealer. If you are unable to insert the plug into the outlet, contact your electrician
to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug.
•
Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. To
disconnect the cord, pull it out by the plug. Never pull the cord itself.
•
Use only the power cord supplied with your device. While appearing to be similar, other power cords have not been safety
tested at the factory and may not be used to power the device. For a replacement power cord, contact your dealer.
•
Do not operate the projector with a damaged cord. Replace the cord. Do not operate the projector if the projector has been
dropped or damaged - until it has been examined and approved for operation by a qualified service technician.
•
Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
•
If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should be used. A cord
rated for less amperage than the projector may overheat.
•
Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short
out parts that could result in a risk of fire or electrical shock.
•
Do not expose this projector to rain or moisture.
•
Do not immerse or expose this projector in water or other liquids.
•
Do not spill liquid of any kind on this projector.
•
Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified service personnel
before resuming operations.
•
Do not disassemble this projector, always take it to an authorized trained service person when service or repair work is
required.
•
Do not use an accessory attachment which is not recommended by the manufacturer.
•
Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused
for long periods of time, unplug it from the wall outlet. This will prevent damage to the device due to lightning and AC
power-line surges.
To prevent personal injury
•
Isolate electrically before replacing the lamp or lamp house. Caution: Hot lamp (house).
•
Caution: High pressure lamp may explode if improperly handled. Refer servicing to qualified service personnel.
•
To prevent injury and physical damage, always read this manual and all labels on the system before inserting the lamp
casing, connecting to the wall outlet or adjusting the projector.
•
To prevent injury, take note of the weight of the projector. Minimum 2 persons are needed to carry the projector.
•
To prevent injury, ensure that the lens and all covers are correctly installed. See installation procedures.
•
Warning: high intensity light beam. NEVER look into the lens ! High luminance could result in damage to the eye.
•
Warning: extremely high brightness lamps:
This projector uses extremely high brightness lamps. Never attempt to
look directly into the lens or at the lamp. If the projection distance is less than 6 meter, any person needs to be at least 4
meters away from the projected image. Avoid close range reflection of the projected image on any reflecting surface (such
as glass, metal, …) . When operating the projector, we strongly recommend wearing suitable safety glasses.
•
Before attempting to remove any of the projector’s covers, you must turn off the projector and disconnect from the wall
outlet.
•
When required to switch off the projector, to access parts inside, always disconnect the power cord from the power net.
•
The power input at the projector side is considered as the disconnect device. When required to switch off the projector,
to access parts inside, always disconnect the power cord at the projector side. In case the power input at the projector side
is not accessible (e.g. ceiling mount), the socket outlet supplying the projector shall be installed nearby the projector and
be easily accessible, or a readily accessible general disconnect device shall be incorporated in the fixed wiring.
•
Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious damage to it and
1.SAFETY
Содержание RLS W12
Страница 1: ...RLS W12 User manual...
Страница 88: ......
