![background image](http://html1.mh-extra.com/html/barco/rlm-w8/rlm-w8_service-manual_4249334005.webp)
- 5 -
z
Introduction of the product & Safety precautions
BARCO (RLM W8) is compact WUXGA (1920 x 1200
Widescreen Ultra Extended Graphics
Array
), and 3-Chip DLP
TM
high-definition images projector. It shares a common
mechanical, electrical, and optical platform.
BARCO (RLM W8) is designed with 0.67” DMD
(Digital Micro mirror Device)
with 330W
dual lamp.
1. Cleaning the Projector
A). Cleaning the projector to remove dust and grime will help ensure trouble-free
operation.
1).
Be sure to turn off and unplug the projector at least 30 minutes before cleaning.
Failure to do so could result in a severe burn.
2).
Use only a dampened cloth when cleaning.
Do not allow water to enter the ventilation openings on the projector.
3).
If a little water gets into the projector interior while cleaning,
leave unplugged in a well-ventilated room for several hours before using.
4).
If a lot of water gets into the projector interior when cleaning, have the projector serviced.
B). Cleaning the Projection Lens
*When dust and fingerprints, etc. are on the lens surface, use
the designated glass cleaner (toraysee) to remove it as shown in the
figure at the right. For fingerprints and other soiling that are difficult
to remove with a dry cloth, use a designated glass cleaner (toraysee)
which has been moistened in water and then use a dry cloth
to dry it off. Or, apply a little optic lens cleaner to a clean soft cloth.
(Do not apply the cleaner directly to the lens.
)
Then, lightly wipe the lens
in a circular motion.
Содержание RLM W8
