![background image](http://html1.mh-extra.com/html/barco/rlm-w8/rlm-w8_service-manual_4249334013.webp)
- 13 -
2. Compliance of Safe Repair
Be sure to read this Service Manual before providing services. In the projector, full
consideration is taken to ensure the safety for a fire, electric shock, injury, harmful
radiation, and substance. Therefore, observe the notice described in this Service Manual
so that the safety is kept when providing services. Moreover, be sure to observe the
notice described in the Instruction Manual. Pay attention to the following during service
inspection.
2-1. Cautions during disassembling and assembling
1) This equipment contains parts under high voltage. When making repairs, etc. Be
sure to pull out the power plug beforehand to insure safety.
2) Parts may be very hot immediately after use. Make sure the equipment has
cooled off sufficiently before carrying out repairs.
3) Make sure that parts and screws and wiring, etc. are returned to their original
positions. Tube, tape and other insulation materials have been used for safety
reasons. The internal wiring has been designed to avoid direct contact
with hot parts or parts under high voltage when using clamps or other tools.
4) The parts used in this device have special safety features such as
flame-resistance and anti-voltage properties. When replacing parts, always use
parts supplied from the factory.
5) After finishing operations make sure that all parts and wires have been returned
to their original position and that there has been no deterioration of the area
around the location that was worked on.
6) Be sure to use an earth band (wrist band) during repair and inspection.
2-2. Lens
Do not look through a lens during projection. This damages your eyes.
Содержание RLM W8
