![background image](http://html1.mh-extra.com/html/barco/r9002260/r9002260_owners-manual_4227495019.webp)
Controlling
4-2
5976053 BARCODATA 808s SP 010799
The BARCOREALITY 812HS can be controlled with
a. The RCU
b. The hardwired RCU (cable not included)
c. The local keyboard
The procedure and results of controlling the projector with either of
these RCU options is essentially the same.
How to use your RCU
a) Point the front of the RCU towards the reflective screen surface
b) Point the front of the RCU towards one of the IR sensors in the
projector.
When using the wireless remote control, make sure you are within
the effective operating distance (30m, 100ft in a straight line). The
remote control unit will not function properly if strong light strikes the
sensor window or if there are obstacles between the remote control
unit and the projector's IR sensor.
c) RCU used in a hardwired configuration.
Plug one end of the remote cable in the connector on the bottom of
the RCU and the second side in the connector in the rear panel of the
BARCODATA 808s SP labelled '
REMOTE
'.
The projector's address will be displayed in a 'Text box'. This text box
disappears after a few seconds.
To continue using your RCU, it is necessary to enter the same address
with the digit buttons (address between 0 and 9). For exemple, if the
Adrress Key displays projector address 003, then press the "3" digit
button on the RCU to set the RCU's address to match the projector's
address. Do not press digit 003. This will address the remote to '0'
and control all projectors in the room.
PROJECTOR
ADDRESS
001
RCU
IR sensor
21
2))
POWER / MAIN S
SH U LSKHUDO V
5
*
%
&RPS+6\QF96\QF
COM M. PO RT
PORT 3
PORT 4 /5
9QRP
, QRP
)U HT
6 H HL QV WD O OD WLRQ LQVW UXFW LR QV EH I RU H FRQQ H FWL QJ W RW KHV XS SO\
9 RLU OD Q RWL F H GLQ V WD OOD WLR QD Y D QW GH UD FF RUGHU D X Up VH D X
9
$PS
+]
6 9, '( 2
2)) 21
2KP
9, '(2
JUHHQ RSHUDW LRQ
UHGVWDQGE\
PORT 2
PORT 1
2)) 21
2KP
PROJECT OR M ODE
7 KLV GH YLF HF RP S O LHV ZL WKS DU W RI
WK H )&&U XO HV 2S HU DW LR Q LV VXE M HFWWR
IR OOR ZLQ J WZR F RQ GL WLR QV 7K L V
G HYL FHP D \Q RW FD XVH K DU PIXO L QW HU
IH UH QF HD QG WK LV GHY LFH PXVW
DF FHS W DQ \ LQ WH UI HU HQ FH UH FHLY HG
L Q FOX GL QJ LQ WH UI HU HQFH WKD WP D \FDXV H
X QG HVL UHGR S HU DWL RQ
5
6
,
1
5
6
2
8
7
,5
5
(
0
2
7
(
56,1
56287
,5
5(027(
PO
RT
4
/5
PO
RT
3
CO
MM
. P
OR
T
PORT 2
PO
RT
1
PR
O JE
CT
OR
M
OD
E
PO
WE
R /
M
AIN
S
Projector Address
a. Hardware set up of the projector address.
Every projector requires an individual address between 0 and 255
which is set with hardware DIP switches inside the projector. To
change that address, contact a BARCO authorized technician.
b. How to control the projector.
The projector's address may be set to any value between 0 and 255.
When the address is set, the projector can be controlled now with:
- the RCU for addresses between 1 and 9.
- computer, e.g. IBM PC (or compatible), Apple MAC, etc. for
addresses between 0 and 255.
Note : A projector will respond to a RCU set to an address of '0'
regardless of what address is set in the projector itself. Address "O"
is therefore a universal address.
c. Using your RCU.
Before using your RCU, it is necessary to enter the projector address
into the RCU (only when that address is between 1 and 9). The
projector with the corresponding address will listen to that specific
RCU.
When address 0, 'zero address' is programmed into the RCU, every
projector, without exception will listen to the commands given by this
RCU.
How to display a projector address?
Press the ADDRESS key (recessed key on the RCU) with a pencil.