Barco R9001560 Скачать руководство пользователя

Страница: 51 / 59

Service Mode

10-5

5976052 BARCOREALITY 9300 070999

Select with or

then <ENTER>

<EXIT> to return.

LAMP DRIVE MODE

SILENT

NORMAL

BOOST

Select with or

then <ENTER>

<EXIT> to return.

Lamp Run Time History

To get an overview of the different lamp run times :

Push the cursor key

to highlight 'Lamp Run Time

History'.

Press

ENTER

to select.

A listing with the lamp serial number and the corresponding run time

will be displayed.

The actual installed lamp will be marked.

Press

EXIT

to return to the service mode selection menu.

SERVICE

IDENTIFICATION

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJ. ADDRESS

CHANGE BAUDRATE PC

RESET LAMP RUNTIME

LAMP RUNTINE HISTORY

LAMP DRIVE MODE

MORE...

LAMP RUNTIME HISTORY

Serial No

Runtime

-----------------------------------------------------

0111121

600 h

0110031

980 h

0110010

1000 h

-----------------------------------------------------

<EXIT> to return

SERVICE

IDENTIFICATION

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJ. ADDRESS

CHANGE BAUDRATE PC

RESET LAMP RUNTIME

LAMP RUNTINE HISTORY

LAMP DRIVE MODE

Lamp Drive Mode

The lamp can be driven in three different modes : SILENT, NORMAL

or BOOST.

Push the cursor key

to highlight 'Lamp Drive Mode'.

Press

ENTER

to select.

Push the cursor key

to highlight the desired lamp drive

mode.

Press

ENTER

to select.

BARCO logo

The BARCO logo can be added to the image, in overlay or on a

background, on any place on the screen.

To add the BARCO logo or to change a setting in the BARCO logo

menu:

Push the cursor key

to highlight 'BARCO logo'.

Press

ENTER

to select.

The BARCO logo menu will be displayed on the screen. Within this

menu, three toggle settings and a shift control are available.

STATUS [ON/OFF]

ON : BARCO logo will be displayed on the screen.

OFF : No BARCO logo displayed on the screen.

BACKGROUND [ON/OFF]

ON : BARCO logo will be displayed on a black background.

OFF : BARCO logo will be displayed without any background.

SHIFT

By pushing the control disc up, down, to the left or to the right, the

BARCO logo can be positioned anywhere on the screen.

HOT KEY [TEXT/OFF]

OFF : no key on the RCU is used to display the BARCO logo.

TEXT : the TEXT key on the RCU is used to display or to remove the

BARCO logo with one single push on this key (only in operational

:mode).

SERVICE

BARCO LOGO

PANEL ADJUSTMENTS

UNIFORMITY

PRESET INPUT BALANCE

I2C DIAGNOSIS

MORE...

BARCO LOGO

STATUS : ON

BACKGROUND : ON

SHIFT

HOT KEY : TEXT

Select with or

then <ENTER>

<EXIT> to return.

Содержание R9001560




























































Результаты поиска

Содержание R9001560

Отзывы:

Похожие инструкции для R9001560

Бренды по названию

Популярные бренды

Barco R9001560, Руководство пользователя

Результаты поиска

Содержание R9001560

Отзывы:

Похожие инструкции для R9001560

Бренды по названию

Популярные бренды