Barco PH series, Руководство пользователя и инструкция по установке

Страница: 97 / 143

10. Lamp replacement
10. LAMP REPLACEMENT
10.1 Lamp replacement warnings
Warnings
• Be careful not to drop the lamp fi xing screws into the inside of the projector. Don’t put a metal piece or fl ammable object into the
projector. Using the projector with any foreign object present inside may result in electric shock or fi re. When you can’t remove
the foreign object from the inside, contact your dealer for removal.
• Do not touch the lamp with bare hands or give a shock to the lamp. Attach the lamp properly. Improper handling may cause
explosion.
• Be sure to install the lamp securely. When the lamp isn’t installed properly, it won’t illuminate. Improper installation may also
result in
fi re.
• Don’t shake the removed lamp or don’t lift it above your face. You may be injured in your eye by fl ying or falling glass fragments.
• Don’t replace the lamp immediately after use because the lamp cover is very hot. You may get burned. Turn off the power
using the POWER key. After the lamp goes out, wait about 2 minutes until the intake and exhaust fans for cooling the lamp
stop rotating. Then unplug the power cord, and wait at least 1 hour to allow the lamp to cool down enough to the touch.
10.2 Interval of lamp replacement
About the lamp
This projector is equipped with 2 lamps to project images. This lamp is a consumable. It may burn out or its brightness may decrease
during use. In such cases, replace the lamp with a new one as soon as possible. Be sure to replace the lamp with a new lamp
separately sold that is exclusive to this projector. Contact your dealer for purchase of the lamp.
Spare lamp: H LAMP 350W
About lamp replacement interval
The recommended interval of lamp replacement is about 4000 hours
12
of consecutive use. Such interval differs depending on the
operating environment and may be shorter than 4000 hours
12
. Decrease in luminescence and/or color brightness indicates that the
lamp needs to be replaced. When the lamp operation time exceeds 3000 hours
1
, the lamp replacement message will appear on
the screen for 1 minute everytime the lamp is turned on. When the lamp has been used for about 3800 hours
1
, the replacement
message (IT’S TIME FOR LAMP * REPLACEMENT) will appear on the screen for 1 minute every 20 hours
1
thereafter. When the
lamp operation time exceeds 4000 hours 12 , the projector automatically shuts off.
Caution
• Don’t remove the lamp for any purpose other than replacement. Unnecessary removal of the lamp may result in a breakdown.
• This projector uses a high-pressure mercury lamp as the light source. The high-pressure mercury lamp may explode or fail
to illuminate permanently because of an impact, scratch, or deterioration through use. The period of time until explosion or
permanent failure to illuminate varies considerably from lamp to lamp, depending on operation conditions. Therefore, the lamp
may explode soon after the start of use.
• The possibility of explosion of the lamp increases if you use it beyond its replacement period. When the instruction of lamp
replacement appears, replace it with a new one immediately even if the lamp is still lighting normally.
• When the high-pressure mercury lamp explodes, glass fragments will scatter inside or outside the lamp box and the gas charged
inside the lamp will diffuse inside or outside the projector. The gas inside the lamp contains mercury. Be careful not to breathe
it or avoid it from entering your eye or mouth. If you should breathe it or if it should enter your eye or mouth, see a doctor
immediately.
• In the event that the high-pressure mercury lamp exploded, glass fragments may have been scattered inside the projector. Ask
your dealer to replace the lamp and to inspect the inside of the projector. When you clean or replace the lamp by yourself, be
sure to hold the handle of the lamp. You may get injured by glass fragments.
• When removing the lamp from the ceiling-mounted projector, use the lamp replacement tray packed with the projector or option
lamp to prevent glass fragments from scattering.
• Be sure to use the lamp exclusive to this projector, H LAMP 350W. Use of other lamps may cause a failure of the projector.
Before replacing the lamp
Check which lamp is to be replaced using the INFO menu in the OSD Lite menu.
1. Duration when LAMP MODE of the INSTALLATION 1 menu is set to LOW. When it is set to STANDARD, this duration will be shorted.
2. When LAMP MODE is set to STANDARD, this duration will be shorted to 2000 hours.
R5905597 PHXX SERIES 20/05/2014 93
Downloaded From projector-manual.com Barco Manuals