Barco Loki Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 128

background image

601

–

0445 /05

Loki

46

4.4.5 Going from READY to ECO standby

Description

If ECO Standby mode is enabled in the service menu (refer to the section "GUI - system settings/Standby
ECO", in User Guide) the projector will automatically go to

ECO

standby mode after a time-out (default 15

minutes). All electronics (including fans, pumps,...) go down except for a very small wake up controller. The

Power on/off

button will FLASH WHITE every second.

4.4.6 Going from ECO to ON

Description

Press the

Power on/off

button on the projector, or the

Power On

button on the remote control. The projector

goes from

ECO

directly to

ON

. The projector will go through the same booting phase as on power plugging,

then do the transition from

READY

to

ON

. Of course startup-time will be longer then from

READY

to

ON

.

4.4.7 Wake On LAN (WOL)

About

The projector has WOL functionality, that can be used for the projector to go from ECO mode to READY
mode. Use a json command for transition from READY to ON.

The WOL is performed by sending a Magic Packet followed by the projectors MAC address. The MAC
address is found in the menu

Home / System settings / Communication / LAN.

The MAC address is similar to

the HW address that is shown in this menu path.

The LAN cable must be connected when the projector enter the ECO mode, in order to obtain the
Wake on LAN function.

4.5 Power modes

General

The table below details the Loki power modes.

Mode

Description

Normal

Projector is booted up and the light source is on

Ready

Projector is booted up but the light source is off

ECO Standby

Light source is switched off and projector electronics
are powered down

4.6 Customize projector settings

About

The projector display, behavior and user interface can be adjusted to meet individual requirements.

Options include:

Home/System Settings/Themes

•

Adjust the OSD menu color

4.7 User interface

Overview

•

On Screen Display (OSD)

Getting started

«
...
44
45
46
47
48
...
»

Содержание Loki

































































































































Отзывы:

Нет отзывов

Похожие инструкции для Loki

ADVANTAGE ELECTROL

Бренд: Da-Lite Страницы: 2

Бренд: Panasonic Страницы: 138

Бренд: Eaton Страницы: 2

PJL1035 - LCD Projector SXGA

Бренд: ViewSonic Страницы: 53

TheaterCurved Reference X-Mask T-X4R

Бренд: Screen Research Страницы: 74

Бренд: Eiki Страницы: 56

Бренд: M-system Страницы: 5

Бренд: CyberPower Страницы: 1

Бренд: Panasonic Страницы: 131

Бренд: CyberPower Страницы: 2

Бренд: Tripp Lite Страницы: 12

Бренд: Hitachi Страницы: 92

Бренд: Hitachi Страницы: 162

Бренд: Hitachi Страницы: 99

Бренд: Hitachi Страницы: 72

50V720 - 50" Rear Projection TV

Бренд: Hitachi Страницы: 72

Бренд: Hitachi Страницы: 60

Бренд: Hitachi Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды