Barco HDF W series Скачать руководство пользователя

Страница: 260 / 319

14. Service

Image 14-3
Identi

cation

Use the

▲

▼

key to scroll through the menu.

14.2 Diagnosis

What can be seen?

The diagnosis menu gives the possibility to get an overview of the working of the projector.
•

•

•

•

•

•

14.2.1 Versions

About versions

The table gives an overview between the reference software and the current installed software.

The reference software is the latest correctly installed package.

The current is the updated software (upgrade of downgrade).

Once the complete current is updated with new software, then this current becomes the new reference.

= means that the current software is equal to the latest reference.

> the current has a higher version than the reference software.

< the current has a lower version than the reference software.

How to display an overview

Press

Menu

to activate the menus and select

Service

→

Diagnosis

→

Versions

256

R5905158 HDF SERIES 16/06/2015

Содержание HDF W series
































































































































































































































































































































Результаты поиска

Содержание HDF W series

Отзывы:

Похожие инструкции для HDF W series

Бренды по названию

Популярные бренды

Barco HDF W series, Инструкция по использованию и установке

Результаты поиска

Содержание HDF W series

Отзывы:

Похожие инструкции для HDF W series

Бренды по названию

Популярные бренды