Location and Functions of Control
2-1
5976283 BARCOGRAPHICS 808s 160501
2
LOCATION AND FUNCTION OF CONTROLS
REAR PANEL TERMINOLOGY
1
AC Power Switch :
to switch on the projector.
Depending on the set-up of the projector during installation, the projector switches to standby or to 'Operational mode. If in standby,
the standby LED lights up.
2
AC Power Input :
connect the supplied AC power (mains) cord here and to the wall outlet.
3
Communication Port
(800 peripherals)
* Allows communication between the RCVDS switcher and the projector.
* Allows connection of a remote IR receiver unit to the projector.
4
Port 3
RGB Analog Input (9 pin female sub D connector). Allows a character generator, microcomputer, etc. having analog RGB outputs
to be connected to the projector.
5
Port 4/5 : RGB-S Input (5x BNC connector)
:
RGB-S input
: allows a character generator, microcomputer, video camera, etc. having analog RGB output to be connected to the
projector.
Line inputs: - Signals RED-GREEN-BLUE
- COMPOSITE sync. signal
- Tri level sync signal (option)
6
S-VIDEO Input
: Separated Y/C (luma-chroma) signal inputs and outputs for higher quality playback of Super VHS signals (4-pin S-
VIDEO connector loop-through).
7
75 ohm Termination Switch for S- Video signals
8
VIDEO Input (Composite video, 2x loop-through BNC connector)
: Allows a video tape recorder, video camera, color receiver/
monitor, etc. having video line output to be connected to the projector.
9
75 ohm Termination Switch forVideo signals
10
IR Remote
Connector for remote input for hard wired remote control
11
Projector Pilot Lamp
: Indicates the status of the projector.
- Unlit : mains (power) switch is not pressed.
- Lit : mains (power) switch is pressed and the indicated color shows the projector mode:
Green color : operational mode of the projector.
Red color : standby mode of the projector.
Important : projector ("Operational" or "Standby") mode is defined during the installation of the projector. (Refer to a qualified
technician for change).
12
IR Sensor
Receiver for control signals transmitted from the RCU.
13
RS 232 Output Port
RS 232 Input Port allows a communication link for PC or MAC to the next projector in a series of projector.
14
RS 232 Input Port
Connection between the projector and an IBM PC (or compatible) or MAC (RS422) for remote computer control and data communication.
21
2))
POWER / MAINS
SHULSKHUDOV
5
*
%
&RPS+6\QF96\QF
COMM. PORT
P ORT 3
P ORT 4/5
9QRP
,QRP
)UHT
6HHLQVWDOODWLRQLQVWUXFWLRQVEHIRUHFRQQHFWLQJWRWKHVXSSO\
9RLUODQRWLFHGLQVWDOODWLRQDYDQWGHUDFFRUGHUDXUpVHDX
9
$PS
+]
69,'(2
2))21
2KP
9,'(2
JUHHQRSHUDWLRQ
UHGVWDQGE\
PORT 2
P ORT 1
2))21
2KP
PROJE CTOR MODE
1
2
3
4
5
7
6
8
9
10
7KLVGHYLFHFRPSOLHVZLWKSDUWRI
WKH)&&UXOHV2SHUDWLRQLVVXEMHFWWR
IR OORZLQ JWZR FRQG LWLRQV 7KLV
GHYLFHPD\QRWFDXVHKDUPIXOLQWHU
IHUHQFHDQGWKLVGHYLFHPXVW
DFFHSWDQ\LQWHUIHUHQFHUHFHLYHG
LQFOXGLQJLQWHUIHUHQFHWKDWPD\FDXVH
XQGHVLUHGRSHUDWLRQ
