![background image](http://html1.mh-extra.com/html/barco/fs40-4k/fs40-4k_safety-manual_4141681004.webp)
R5913246 /00
FL-FS40 MKII SERIES
4
Do not operate the projector if the projector has been dropped or damaged - until it has been examined and approved for operation by
a qualified service technician.
•
Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
•
If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should be used. A cord rated for less
amperage than the projector may overheat.
•
Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts
that could result in a risk of fire or electrical shock.
•
Make sure that no objects enter into the vents and openings of the set.
•
Do not expose this projector to rain or moisture.
•
The projector is designed for indoor use only. Never operate the unit outdoors.
•
Do not immerse or expose this projector in water or other liquids.
•
Do not spill liquid of any kind on this projector.
•
Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified service personnel before
resuming operations.
•
Do not disassemble this projector, always take it to an authorized trained service person when service or repair work is required.
•
Do not use an accessory attachment which is not recommended by the manufacturer.
•
Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will prevent damage to the device due to lightning and AC power-line surges.
To prevent personal injury
•
To prevent injury and physical damage, always read this manual and all labels on the system before connecting to the wall outlet or
adjusting the projector.
•
To prevent injury, take note of the weight of the projector.
•
To prevent injury, ensure that the lens and all covers are correctly installed. See installation procedures.
•
Warning: high intensity light beam. NEVER look into the lens! High luminance could result in damage to the eye.
•
Always switch off the projector and disconnect from the mains power supply before attempting to remove any of the projector covers or
access parts inside the projector.
•
This product contains no user serviceable parts. Attempts to modify/replace mechanics or electronics inside the housing or
compartments will violate any warranties and may be hazardous.
•
Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious damage to it and possible injury
to the user.
•
Only place the projector on a stable surface, or mount it securely using an approved ceiling-mount.
To prevent fire hazard
•
Barco projection products are designed and manufactured to meet the most stringent safety regulations. This projector radiates heat
on its external surfaces and from ventilation ducts during normal operation, which is both normal and safe. Exposing flammable or
combustible materials into close proximity of this projector could result in the spontaneous ignition of that material, resulting in a fire.
For this reason, it is absolutely necessary to leave an
“
exclusion zone
”
around all external surfaces of the projector whereby no
flammable or combustible materials are present.
•
Do not place flammable or combustible materials near the projector!
•
Caution! Hot air is exhausted from the rear vent. Do not place objects that are sensitive to heat nearer than 25 cm (10
”
) to the exhaust
vent.
•
Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the projector and to protect it from
overheating, these openings must not be blocked or covered.
•
The openings should never be blocked by placing the projector too close to walls, or other similar surface. Allow for sufficient distance
to walls and ceilings to avoid overheating. Minimum safety distance to the exhaust area of the unit must not be less than 25 cm (10
”
)
and to the intake area, not less than 25 cm (10
”
).
•
This projector should never be placed near or over a radiator or heat register.
•
This projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
•
Do not cover the projector or the lens with any material while the projector is in operation. Keep flammable and combustible materials
away from the projector at all times.
•
Mount the projector in a well-ventilated area away from sources of ignition and out of direct sun light. Always allow ample airflow
through the projector.
•
Never expose the projector to rain or moisture. In the event of fire, use sand, CO2 or dry powder fire extinguishers.
•
Never use water on an electrical fire.
•
Always have service performed on this projector by authorized Barco service personnel. Always insist on genuine Barco replacement
parts. Never use non-Barco replacement parts as they may degrade the safety of this projector.
•
Projection rooms must be well ventilated or cooled in order to avoid heat buildup.
•
Let the projector cool down completely before storing. Remove cord from the projector when storing.
To prevent projector damage
•
To ensure correct airflow is maintained, the projector should only be operated when all of its covers in place. The exception from this is
the front cover, that can be removed to give access to multiple anchor points. See User Guide for more detailed info regarding this
issue.
•
Always remove lens cap before switching on the projector. If the lens cap is not removed, it may melt due to the high energy light
emitted through the lens. Melting the lens cap may permanently damage the surface of the projection lens
•
Only connect the projector to signal sources and voltages as described in the technical specification. Connecting to unspecified signal
sources or voltages may lead to malfunction and permanent damage of the unit.
•
To ensure correct airflow is maintained, it should only be operated when all of its covers are in place.
•
The projector must always be installed in a manner which ensures free flow of air into its air inlets and unimpeded evacuation of the
hot air from its cooling system.
•
Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from
overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed,
Содержание FS40 - 4K
Страница 1: ...ENABLING BRIGHT OUTCOMES Safety Manual FL FS40 MKII SERIES...
Страница 10: ...R5913246 00 FL FS40 MKII SERIES 10 Safety and environmental information...
Страница 11: ......