R5909934 /00
E2 Lite and EC-40
29
The E2 Lite works only with the EMTS version 6.4.
3.8 Initial inspection
General
Before shipment, all the devices were inspected and found to be free of mechanical and electrical defects. As
soon as the devices are unpacked, inspect for any damage that may have occurred in transit. Save all packing
material until the inspection is completed. If damage is found, file claim with carrier immediately. The Barco
Sales and the Service office should be notified as soon as possible.
Unpacking
At delivery, Event Master devices are packed in a shipping case. Place the shipping case of the device on a
stable (solid), flat and insulated support during all the unpacking. Open the case from the top. Remove the
device that is packaged in an antistatic bag. Check the box content after unpacking.
After unpacking let the device acclimate to the room temperature which must be higher than 0°C
(32°F) and lower than 40°C (104°F). Neglecting this may result in startup failure of the device.
Save the original shipping case and packing material, these will be necessary if you ever have to
ship your device. For maximum protection, repack your device as it was originally packed at the
factory.
When shipping an E2 Lite in a Barco-supplied case, make sure that the rear connector protectors
are installed to prevent damage.
Box content
After unpacking an Event Master device, it is recommended that it be checked to see if all accessories were
included.
Depending on the product, the following accessories should be included.
Product
Contains
Accessories included
R9009198CN
(E2 Lite)
4RU rack mount
chassis
•
E2 Lite assembly
•
2x Z3487505
•
China Power Cord GB 2099 (included only with units shipped to
China)
•
2x 09-0106032-91
•
Rear Rack Mount Support Plates
•
8x 13-0081012-90
•
8-32 x .38 Pan Head Screws for Rear Rack Mount Support
Plates
•
2x 09-0106031-90
•
Rear Rack Mount Brackets
•
07-1205500-00
•
USB Thumb Drive (Contains Users Guide, System Software
and
Control GUI)
•
R5909936
•
Safety guide
•
26-1205005-00
•
Quick start guide
R9009085CN
(EC-40)
EC controller
•
EC-40 assembly
•
1x Z3487505
•
China Power Cord GB 2099 (included only with units shipped to
China)
•
1x R9080005
•
Dust Cover
•
1x 90409546EF
•
USB Type A to Type B Cable
Содержание Event Master E2 Lite
