1. Safety & Environmental Information
To prevent
fi
re hazard
•
Do not place
fl
ammable or combustible materials near the projector!
•
Barco large screen projection products are designed and manufactured to meet the most stringent safety regulations. This
projector radiates heat on its external surfaces and from ventilation ducts during normal operation, which is both normal and
safe. Exposing
fl
ammable or combustible materials into close proximity of this projector could result in the spontaneous ignition
of that material, resulting in a
fi
re. For this reason, it is absolutely necessary to leave an “exclusion zone” around all external
surfaces of the projector whereby no
fl
ammable or combustible materials are present. The exclusion zone must be not less
than 40 cm (16”) for this projector. The exclusion zone on the lens side must be at least 5 m. Do not cover the projector or the
lens with any material while the projector is in operation. Keep
fl
ammable and combustible materials away from the projector at
all times. Mount the projector in a well ventilated area away from sources of ignition and out of direct sun light. Never expose
the projector to rain or moisture. In the event of
fi
re, use sand, CO
2
or dry powder
fi
re extinguishers. Never use water on an
electrical
fi
re. Always have service performed on this projector by authorized Barco service personnel. Always insist on genuine
Barco replacement parts. Never use non-Barco replacement parts as they may degrade the safety of this projector.
•
Ensure no misalignment can occur. Prolonged exposure of wooden walls at close distance (< 20 cm) can represent a
fi
re risk.
After alignment the projector shall be securely mounted to the pedestal.
•
Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the projector and to protect
it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the
projector too close to walls, or other similar surface. This projector should never be placed near or over a radiator or heat
register. This projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
•
Projection rooms must be well ventilated or cooled in order to avoid build up of heat. It is necessary to vent hot exhaust air from
projector and cooling system to the outside of the building.
•
Let the projector cool completely before storing. Remove cord from the projector when storing.
To prevent battery explosion
•
Danger of explosion if battery is incorrectly installed.
•
Replace only with the same or equivalent type recommended by the manufacturer.
•
For disposal of used batteries, always consult federal, state, local and provincial hazardous waste disposal rules and regulations
to ensure proper disposal.
To prevent projector damage
•
The air
fi
lters of the projector must be cleaned or replaced on a regular basis. Cleaning the booth area would be monthly-
minimum. Neglecting this could result in disrupting the air
fl
ow inside the projector, causing overheating. Overheating may lead
to the projector shutting down during operation.
•
The projector must always be installed in a manner which ensures free
fl
ow of air into its air inlets.
•
If more than one projector is installed in a common projection booth, the exhaust air
fl
ow requirements are valid for EACH
individual projector system. Note that inadequate air extraction or cooling will result in decreased life expectancy of the projector
as a whole as well as causing premature failure of the lasers.
•
In order to ensure that correct air
fl
ow is maintained, and that the projector complies with Electromagnetic Compatibility (EMC)
and safety requirements, it should always be operated with all of it’s covers in place.
•
Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from
overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product
on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. The
device should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
•
Ensure that nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and remove all power
from the projector. Do not operate the projector again until it has been checked by quali
fi
ed service personnel.
•
Do not block the projector cooling fans or free air movement around the projector. Loose papers or other objects may not be
nearer to the projector than 10 cm (4") on any side.
•
Proper operation of the projector can only be guaranteed in table mounting. It is not permitted to use the projector in another
position. See installation procedure for correct installation.
•
Special care for Laser Beams
: Special care should be used when DLP projectors are used in the same room as high power
laser equipment. Direct or indirect hitting of a laser beam on to the lens can severely damage the Digital Mirror Devices
TM
in
which case there is a loss of warranty.
•
Never place the projector in direct sunlight. Sunlight on the lens can severely damage the Digital Mirror Devices
TM
in which
case there is a loss of warranty.
•
Save the original shipping carton and packing material. They will come in handy if you ever have to ship your equipment. For
maximum protection, repack your set as it was originally packed at the factory.
•
Remove all power from the projectors mains terminals before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning. Never use strong solvents, such as thinner or benzine or abrasive cleaners, since these will damage
the cabinet. Stubborn stains may be removed with a cloth lightly dampened with mild detergent solution.
•
To ensure the highest optical performance and resolution, the projection lenses are specially treated with an anti-re
fl
ective
coating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry cloth. For lens cleaning follow the
instructions precisely as stipulated in the projector manual.
•
Rated maximum ambient temperature, t
a
= 35°C (95°F).
•
Rated humidity = 5% to 85% RH Non-condensed.
•
An external frame must be used to stack projectors.
4
R5906846 DP2K-SLP SERIES 11/05/2017
