![background image](http://html1.mh-extra.com/html/barco/data-2100-r9001070/data-2100-r9001070_owners-manual_4060123044.webp)
Power Connection
6-4
Power Connection
5975696 BARCODATA 2100 140798
5975696 BARCODATA 2100 140798
6-4
Lamp Lifetime
30 hours before end of lamp lifetime, the following message will scroll over the screen for 1
minute. This message will be repeated every 30 minutes. Press EXIT to remove the message
before the minute is over.
When the end of the lamp lifetime is reached, the following message, with the exact run time
is displayed on the screen.
Lamp run time is 1000* hours. Operating the lamp longer than 1000 *hours may damage the
projector. Please replace the lamp.
Switching OFF
To switch off:
- press first
STANDBY
key and let cool down until the fans
stop blowing ( or at least 15 min).
- switch off the projector with the power switch.
Remaining
Lamp run
time: 20 hours
Article
Numbre
Dimming / Lamp
Drive Mode
Lamp
Lifetime
R9829510
Dimming
1000
R9829600
Economic
Normal
3500
2000
R9829740
Dimming
4000
When OK (ENTER) is pressed to go on, the warning will be repeated
every 30 min.
* The total lifetime of the lamp for a safe operation is depending on
the type of lamp and on the operating mode. The different values are
shown in Table 1.
Do not use it longer. Replace always with a same type of lamp. Call
a BARCO authorized service technician for lamp replacement.
Warning : Using a lamp for more than Lamp Lifetime
is dangerous, the lamp could explode.
Note: Switching the projector OFF and ON again,
adds 45 minutes to the lamp run time.
Switching to Stand-by.
When the projector is running and you want to go to stand-by, press
the stand-by key.
Caution
: Before powering down the projector, switch the projector
to stand-by and let the projector lamp cool down until the fans stop
blowing (or for at least 15 minutes).
Lamp Lifetime
30 hours before end of lamp lifetime, the following message will scroll over the screen for 1
minute. This message will be repeated every 30 minutes. Press EXIT to remove the message
before the minute is over.
When the end of the lamp lifetime is reached, the following message, with the exact run time
is displayed on the screen.
Lamp run time is 1000* hours. Operating the lamp longer than 1000 *hours may damage the
projector. Please replace the lamp.
Switching OFF
To switch off:
- press first
STANDBY
key and let cool down until the fans
stop blowing ( or at least 15 min).
- switch off the projector with the power switch.
Remaining
Lamp run
time: 20 hours
Article
Numbre
Dimming / Lamp
Drive Mode
Lamp
Lifetime
R9829510
Dimming
1000
R9829600
Economic
Normal
3500
2000
R9829740
Dimming
4000
When OK (ENTER) is pressed to go on, the warning will be repeated
every 30 min.
* The total lifetime of the lamp for a safe operation is depending on
the type of lamp and on the operating mode. The different values are
shown in Table 1.
Do not use it longer. Replace always with a same type of lamp. Call
a BARCO authorized service technician for lamp replacement.
Warning : Using a lamp for more than Lamp Lifetime
is dangerous, the lamp could explode.
Note: Switching the projector OFF and ON again,
adds 45 minutes to the lamp run time.
Switching to Stand-by.
When the projector is running and you want to go to stand-by, press
the stand-by key.
Caution
: Before powering down the projector, switch the projector
to stand-by and let the projector lamp cool down until the fans stop
blowing (or for at least 15 minutes).