4. Getting Started
4.6.2
Displaying and Programming addresses
Displaying the Projector Address on the Screen.
1. Press
Address
key (recessed key on the RCU) with a pencil.
The projector’s address will be displayed in a ’Text box’
To continue using the RCU with that specific address, it is necessary to enter the same address with the
digit buttons (address between 0 and 9) within 5 seconds after pushing the address key. For example : if the
Address key displays projector address 003, then press "3" digit button on the RCU to set the RCU’s address
to match the projector’s address. Do not press 003 digits. This will address the remote control to ’0’ and
control all projectors in the room. If the address is not entered within 5 seconds, the RCU returns to its default
address (zero address) and control all projectors in the room.
How to Program an Address into the RCU?
1. Press the
Address
key (recessed key on the RCU) with a pencil.
2. Enter the address with the digit buttons within 5 seconds after pushing the address key.
Note:
That address can be any digit between 0 and 9.
4.7 Controlling the projector
4.7.1
Input selection
Input Selection via the RCU
1. Key in the corresponding slot number with the digit keys on the RCU.
The selected source will be displayed.
Input Selection via the Local Keypad
1. Press the
ADJUST
key to display the General access menu.
2. Highlight the desired source number by pushing the control disc up, down, to the left or the right. Push the control disc up or
down to move the cursor up and down, push the control disc to the left or to the right to move the cursor to the left and to the right.
3. Press
ENTER
to confirm your selection.
When the source is selected
When a valid and available source is selected, there will be information displayed on the screen about that source. This information
includes :
•
Source number
•
Horizontal frequency
•
Vertical frequency
When the entry is a non valid source number, a warning appears on the screen :
input not available
.
When a valid source number is selected, the projector will display this source or it will wait on the selected source number until the
source becomes available. A message
source not available
will be displayed for a short time.
4.7.2
Picture controls
Access via the RCU
The control keys are located on the left side of the key panel of the RCU and indicated with the name of the control and an icon.
When an image control is pressed, a text box with bar scale and the function name of the control, e.g. ’brightness...’ appears on
the screen (only if text is ON). The length of the bar scale indicates the current memorized setting for this source. The bar scale
changes as the + or - side of the button of the control are pressed.
Access via the local keypad
1. Press the
ADJUST
key to display the General access menu.
2. Use the cursor keys to highlight the desired analog control.
3. Press
ENTER
to select.
28
R5976584 BARCO CINE7 26022003
Содержание CINE7 R9010040
