Barbecook SPRING 3112, Руководство пользователя

Страница: 29 / 297

www.barbecook.com 29
8.3. Before first use (or after a lengthy period out of use)
If you are using the appliance for the first time or after a
lengthy period out of use, you must carry out some additional
checks:
• Ensure that you have read all of the instructions in this
guide, understood them, and checked them (before first
use only).
• Check the appliance for gas leaks. See “7. Checking for
gas leaks”.
Check that there are no gas leaks if the appliance has
been assembled by the supplier.
• Clean the burners and venturi tubes (only after a lengthy
period out of use).
See “11.3 Cleaning the burners and venturi tubes”.
• Allow the appliance to “burn in” before placing any food
on the grill (only before first use). See “8.3 Burning in the
appliance”.
8.4. Burning in the appliance
Burning in the appliance before first use helps to remove any
manufacturing greases that may still be present.
Proceed as follows:
1. Ignite the main burners and set the control knobs to HIGH.
See “9.2 Igniting the main burners”.
2. Close the lid and allow the appliance to burn for 15 minutes.
Do not put any food on the grill yet.
3. After 15 minutes, open the lid and let the appliance burn for
a further 5 minutes (control knobs still set to HIGH).
4. After these 5 minutes, the appliance is ready for use and
you can place food on the grill.
9. IGNITING THE BURNERS
To ignite the burners with the electric igniter, you must
insert an AA battery into the igniter. The battery is not
supplied with the appliance. The battery compartment
for the igniter is located on the control panel for the
appliance.
9.1. Safety instructions
• Before igniting the appliance, carry out all checks as
specified in “8. Preparing the appliance for use”.
• Ensure that the lid is open whenever you ignite a burner.
• Never bend directly over a burner when igniting it.
9.2. Igniting the main burners
9.2.1. Using the igniter
1. Open the lid and set the control knobs for the main burners
to OFF.
2. If no other burner has yet been ignited, open the gas supply
and wait for ten seconds for the gas to stabilize.
3. Press the control knob for a burner, set it to HIGH, and
leave it in place. The in-built igniter will create sparks, which
will ignite the burner.
Start by igniting one main burner first. Never ignite all
main burners at the same time.
4. Continue to press the igniter and set the control knob for
the burner with electrode to HIGH.
A
B
Never attempt to ignite a burner other than the burner with
the electrode first, as this will cause gas to accumulate in
the barbecue.
5. If the burner does not ignite after three attempts,
set the control knob for the burner to OFF, close the gas
supply, and wait for 5 minutes to allow the accumulated gas
to escape.
6. Attempt to ignite the burner again. If it still does not ignite,
attempt to ignite the burner with a match (see 9.2.2. “Using
a match”) or consult “14. Rectifying problems” in order
to identify the cause of the problem.
7. If the burner with electrode has been ignited, you can ignite
the other burners by setting the relevant control knobs to
HIGH (in which case you do not need to press the ignition
button).
9.2.2 Using a match
1. 1. Place a match in the match holder.
2. Open the lid and set the control knobs for the main burners
to OFF.
3. If no other burner has yet been ignited,
open the gas supply and wait for ten seconds
for the gas to stabilize.
4. Strike the match and hold it around 13 mm
away from the burner.
5. Set the control knob for one burner to HIGH.
Start by igniting one main burner first. Never ignite all
main burners at the same time.