Barbco TRIBOR 36 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 47

background image

OPERATION OF BREAKOUT ASSEMBLY:

1-

Make sure the Breakout assembly is properly locked into the track. All four pins are
engaged.

2-

Connect all umbilical hoses between the power pack and breakout assembly.

CAUTION! EQUIPMENT HAZARD!

To start the engine either all the hoses must be

connected or all the hoses must be disconnected

.

Never make umbilical connections when the

engine is running.

3-

The front and rear clamping valve sections have friction hold capabilities. This allows for
constant pressure against the tool joints.

Adjusting the clamping pressure-

4-

Close one of the clamp sections. The set pressure will be displayed on the hydraulic
gauge.

5-

Turn the pressure adjustment knob clockwise to increase the pressure. Turn the knob
counter-clockwise to decrease the pressure.

NOTE- You may need to place the valve in the neutral position to make an adjustment.

Operation 35

«
...
36
37
38
39
40
...
»

Содержание TRIBOR 36
















































Отзывы:

Нет отзывов

Похожие инструкции для TRIBOR 36

Бренд: B&K Страницы: 8

Бренд: GE Страницы: 2

Druck DPI 620 Genii

Бренд: GE Страницы: 154

Arize Element Top Light

Бренд: GE Страницы: 2

Бренд: Datex-Ohmeda Страницы: 104

Druck DPI 620 Genii

Бренд: Baker Hughes Страницы: 166

Druck DPI 620 Genii

Бренд: Baker Hughes Страницы: 340

Бренд: Palazzetti Страницы: 112

SafetuNet Alert

Бренд: Masimo Страницы: 2

AJSPD850P - P2 DECK

Бренд: Panasonic Страницы: 73

Бренд: Danelec Страницы: 67

Бренд: Gaspardo Страницы: 16

Бренд: Gastrodomus Страницы: 4

Бренд: HANYOUNG NUX Страницы: 2

Бренд: Gastrodomus Страницы: 39

Martin ERA 800 Performance

Бренд: Harman Страницы: 32

Martin ERA 600 Performance

Бренд: Harman Страницы: 32

Бренд: Hardt Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды