background image

 

Baracoda ToughRunners – User Guide v1.6 

 

- 13 - 

 

Safety / Regulatory. 

 

FCC: 

Product FCC Id: 

QSHAIBTR 

Interference statement: 

This device complies with Part 15 of the FCC Rules. 
Operation is subject to the following two conditions: 

(1) this device may not cause harmful interference, and  

(2)  this  device  must  accept  any  interference  received,  including  interference  that  may  cause  undesired 
operation. 

Modification statement: 

The  FCC  requires  the  user  to  be  notified  that  any  changes  or  modifications  made  to  this  device  that  are  not 
expressly approved by Baracoda Wireless Technology, may void the user’s authority to operate the equipment. 

Class B digital devices regulatory notice: 

This equipment

 has been tested and found to comply with the limits for a Class B digital device, pursuant to 

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 

interference in a residential installation. This equipment generates, uses, and can radiate radio frequency 

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to 

radio communications. However, there is no guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference to radio or television reception, which can be 

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by 1 

or more of the following measures: 

 

Reorient or relocate the receiving antenna 

 

Increase the separation between the equipment and receiver 

 

Connect  the  equipment  into  an  outlet  on  a  circuit  different  from  that  to  which  the  receiver  is 

connected 

 

Consult the dealer or an experienced radio or television technician for help 

Wireless notice 

This product emits radio frequency energy, but the radiated output power of this device is far below the FCC 

radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential 

for human contact with the antenna during normal operation is minimized. The system antenna(s) used for this 

transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 

 

 

 

 

 

 

Data Capture 

for Workforce 

in Motion 

Содержание ToughRunners

















Отзывы: