Bantam e-Station BC8HP Скачать руководство пользователя страница 18

Display

REVERSE POLARITY   

Display

CONNECTION BREAK  

Display

SHORT ERR  

Display

INPUT VOL ERR

Display

VOL SELECT ERR

Display

BREAK DOWN   

Display

BATTERY CHECK
LOW VOLTAGE   

Display

Display

BATTERY VOLTAGE
         CELL LOW VOL

Warning and error messages

The output is connected to a battery with incorrect polarity.

This will be displayed in case of detecting an interruption of 
the connection between battery and output or voluntarily 
disconnecting the charge lead during the operation of 
charge or discharge on output.

The voltage of one of the cell in the Lithium battery pack is 
too low. Please check the voltage of the cell one by one.

The voltage of Lithium battery pack was selected incorrectly. 
Verify the voltage of battery pack carefully.

The processor detects the voltage is lower than you set at 
Lithium program. Please check the cell count of the battery.

 BC8HP incorporates a various functions of protective and monitoring the system to 
verify functions and the state of its electronics. In any case of occurring error, the 
screen displays the cause of error that is self-explanatory with audible sound.

The processor detects the voltage is higher than you set at 
Lithium program. Please check the cell count of the battery.

Display

There are bad connection at the individual connector. 
Please check the connector and cables carefully.

Display

Display

TEMP OVER ERR

Display

CONTROL FAILURE

There was a short-circuit at OUTPUT. Please check the 
charging leads.

The voltage of input power drops below the limit.

There happens the malfunction at the charger circuit by any 
reason. The charger should be repaired at our factory.

The voltage of one of the cell in the Lithium battery pack is 
too high. Please check the voltage of the cell one by one.

The internal temperature of the unit goes too high. Cool 
down the unit.

The processor can not continue to control the feeding 
current by any reason. The unit needs to be repaired.

BATTERY CHECK
HIGH VOLTAGE   

BATTERY VOLTAGE
        CELL HIGH VOL

BATTERY VOL ERR
      CELL CONNECT

                                             

 

 

- 18 -

   

                                       

+

-

+

-

+

-

+

-

+

-

+

-

-

+

-

+

-

-

+

-

+

-

+

-

+

-

!

!

!

Содержание e-Station BC8HP






















Отзывы: