Banner TCNM-AD Series Скачать руководство пользователя страница 74

Страница: 74 / 92

TCNM-AD/EX/SP Family Software Configuration Parameter Guide

DIGITIZER: Motor Life End

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message when the motor has

surpassed its factory declared functional life.

DIGITIZER: Laser Failure

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message whenever a laser failure has

occurred.

DIGITIZER: Laser Life End

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message when the laser has

surpassed its factory declared functional life.

DIGITIZER: Data Consistency Error

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message whenever a checksum error

has occurred on the analog board EEPROM memory.

DIGITIZER: Data Write Error

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message whenever a data write error
has occurred to the analog board EEPROM memory.

DIGITIZER: Communication Error

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message whenever there is a

communication error between the decoder board and the analog board.

DIGITIZER: Reset

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message whenever an unexpected

analog board reset has occurred.

OSCILLATING MIRROR: Motor Failure

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message whenever an oscillating

mirror motor failure is signaled.

OSCILLATING MIRROR: Motor Life End

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message when the oscillating mirror

motor has surpassed its factory declared functional life.

OSCILLATING MIRROR: Data Consistency Error

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message whenever a checksum error

has occurred on the oscillating mirror onboard settings.

OSCILLATING MIRROR: Data Write Error

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message whenever a data write error

has occurred to the oscillating mirror board EEPROM memory.

OSCILLATING MIRROR: Communication Error

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message whenever there is a

communication error between the decoder board and the oscillating mirror board.

OSCILLATING MIRROR: Reset

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message whenever an unexpected

oscillating mirror board reset has occurred.

Содержание TCNM-AD Series





























































































Результаты поиска

Содержание TCNM-AD Series

Отзывы:

Бренды по названию

Популярные бренды

Banner TCNM-AD Series, Руководство по параметрам

Результаты поиска

Содержание TCNM-AD Series

Отзывы:

Бренды по названию

Популярные бренды