Banner TCNM-AD Series Скачать руководство пользователя страница 37

Страница: 37 / 92

Reading Parameters

Second Zone Trigger Level

This parameter allows setting the active state of the trigger. When the selected state is active, the oscillating mirror

starts working in the second reading zone according to the parameters set:
Selections:

Active Open

Active Closed

Second Zone Oscillating Mode

This parameter defines the oscillating mode of the scanner mirror to be used in the second reading zone:

Selections:

Fixed

the oscillating mirror deflects the scan line at a fixed Second Zone Angle

(default 10°).

Continuous

the scan line is deflected according to the Second Zone Min-Max Angle and
Second Zone Frequency settings.

Second Zone Angle (degrees)

This parameter is available only when the second reading zone is working in

Fixed Second Zone Oscillating Mode

It defines the angle in degrees with respect to the angle perpendicular to the scanner (0°).

The default value is 10°.

Selections: a value from

-5°

35°

Second Zone Min Angle (degrees)

This parameter is available only when the second reading zone is working in

Continuous Second Zone Oscillating

Mode

It defines the minimum angle for the second zone deflection range with respect to the angle perpendicular to the

scanner (0°).

Selections: a value from

-5°

35°

Second Zone Max Angle (degrees)

This parameter is available only when the second reading zone is working in

Continuous Second Zone Oscillating

Mode

It defines the maximum angle for the second zone deflection range with respect to the angle perpendicular to the

scanner (0°).

Selections: a value from

-5°

35°

Second Zone Frequency (Hz)

This parameter is available only when working in

Continuous Second Zone Oscillating Mode

It defines the oscillating frequency in Hertz for the second oscillating zone:

Selections: a value from

0.2

20.0

Hertz:

NOTE

The maximum allowable frequency for the given oscillating amplitudes is:

30.5° to 40°          5 Hz
20.5° to 30°          7 Hz
10.5° to 20°         10 Hz
0.5 to 10°            20 Hz

Содержание TCNM-AD Series





























































































Результаты поиска

Содержание TCNM-AD Series

Отзывы:

Бренды по названию

Популярные бренды

Banner TCNM-AD Series, Руководство по параметрам

Результаты поиска

Содержание TCNM-AD Series

Отзывы:

Бренды по названию

Популярные бренды