WARNING:
•
Connecting safety switches in series
•
Monitoring multiple guards with a series connection of multiple safety interlock switches is not a Safety
Category 4 Application (per ISO 13849-1). A single failure can be masked or not detected at all. The
loss of a safety stop signal or an inappropriate reset can lead to serious injury or death.
•
When such a configuration is used, procedures must be performed regularly to verify proper operation of
each switch. Correct all failures immediately (for example, immediately replace a failed switch).
Specifications
Contact Rating
3 A at 230 V AC max., 1.0 A at 24 V DC max.
2.5 kV maximum rated impulse withstand voltage (U
imp
)
European Rating:
U
i
= 250 V
U
e
= 230 V AC, 24 V DC
Ithe = 4A
Utilization categories:
AC-15: U
e
/I
e
230 V / 3 A; DC-13: U
e
/I
e
24 V / 1 A
(IEC/EN 90497-5-1)
Electrical Protection Class
II, protective insulation
Contact Function
Slow make and break contacts, 2 NC, 1 NO
Wire Connections
6-pin Micro-style quick-disconnect fitting (M12 Dual-Key-Way). Cordsets are
ordered separately.
Construction
SI-HG63..:
Hinge: Cast Stainless Steel (X22CrNi 17); Switch: PBT
SI-HGZ63..:
Hinge: zinc die cast (nickel finish); Switch: PBT
Environmental Rating
IP67 acc. to IEC/EN 60529
W models are IEC IP69 according to IEC/EN 60529
Operating Conditions
–25 °C to +70 °C (–13 °F to +158 °F)
(connecting cable permanently mounted; no freezing over / no condensation)
Mounting
4 × M6 screws DIN EN ISO 7984 (on flat and stiff surface)
Switching Frequency
Max. 300 operations/h (5 operations per minute)
Switching Angle
NC Contact: ± 3°, Positive-opening ± 6° (wear can cause increase by 2°)
NO Contact: ± 9°
Tolerance for all angles: 1.5°
Mechanical Load
SI-HG63..:
F
R1
= 1800 N max., F
R2
= 750 N max., F
A
= 1800 N max.
SI-HGZ63..:
F
R1
= 1200 N max., F
R2
= 500 N max., F
A
= 1200 N max.
For direction of loaded forces, see Operating Range
Mechanical Life
1 million operations
Excessive loading (force) and/or vibration, as well as improper installation,
can reduce the service life.
Weight
SI-HG63..:
approximately 0.45 kg
SI-HG63A:
approximately 0.27 kg
SI-HGZ63..:
approximately 0.4 kg
SI-HGZ63A:
approximately 0.22 kg
Cabled
SI-HG63..:
approximately 0.65 kg
Double
SI-HG63..:
approximately 1 kg
Application Notes
To avoid excessive radial stress in applications containing large doors, the
hinge switch must be mounted either in pairs of two, or in conjunction with a
blank hinge.
Applicable Standards
VDE 0660 T100, DIN EN 60947-1, IEC 60947-1
VDE 0660 T200, DIN EN 60947-5-1, IEC 60947-5-1
B10d
2 × 10
6
cycles (at DC-13; 24 V; I
e2
= 0.1 A)
Short Circuit Protection
4 amp Slow Blow (gG). Recommended external fusing or overload
protection.
Rated conditional short-circuit current: 1000 A
Operating Range
0 to 270°
EU-Conformity
According to directive 2006/42/EG
According to directive 2006/95/EC
Approvals
C
CSA
US
B300
Certifications
Banner Engineering Europe
Park
Lane, Culliganlaan 2F bus 3, 1831
Diegem, BELGIUM
Turck Banner LTD
Blenheim House,
Blenheim Court, Wickford, Essex
SS11 8YT, Great Britain
Dimensions
All measurements are listed in millimeters [inches], unless noted otherwise.
For blank hinge dimensions, see
on page 13.
SI-HG(Z)63 Hinge Wing Safety Interlock Switch
P/N 129465 Rev. G
www.bannerengineering.com - Tel: + 1 888 373 6767
9
