manualshive.com logo in svg

Banner PICO-AMP MD14BB6, Руководство пользователя

Поделиться
Скачать
Banner PICO-AMP MD14BB6 Скачать руководство пользователя страница 6

PICO-AMP Miniature Remote Sensing System

Sensor Models

Opposed-mode emitter/receiver pairs: SP3ER1, SP3ER2, SP8ER1, SP8ER2
Diffuse-mode: SP3D1

Amplifier Compatibility 

MD14

Construction 

Black ABS housing

Environmental Ratings

IP50, NEMA 1

Operating Conditions

Temperature: -20° to 70° C (-5° to +158°F)
Maximum relative humidity: 90% at 50° C (non-condensing)

Application Notes

Avoid mounting sensor wires near high-current circuits or inductive sources.
Always remove power to amplifier before connecting or disconnecting sensors.
Sensor cable length should not exceed 9 m (30').

Indicators 

Yellow: ON Steady = Light is sensed    NOTE: This indicator is located on the emitter of opposed-mode sensors.

Mounting Hardware 

Two each M2 x 0.4 mm x 8 mm Phillips pan-head zinc-plated steel machine screws, flat washers,
lockwashers, and hex nuts for each sensor

Connections

2-part parallel/joined coaxial cable: Each part is PVC-jacketed, .065" O.D., 2-conductor 2 m (6.5') cable
with 28 AWG insulated center conductor and spiral wrap shield

SP3/SP8 Remote Sensor Specifications

SP3/SP8 Dimensions

7.5 mm

(0.30")

5.0 mm

(0.20")

2.3 mm

(0.09")

2.2 mm

(0.09")

5.9 mm

(0.23")

12.0 mm

(0.47")

15.0 mm

(0.59")

Lens

Indicator for

Light Sensed

(Emitters only)

3.8 mm

(0.15")

7.9 mm

(0.31")

2x ø2.2 mm

(0.09")

3.0 mm

(0.12")

7.5 mm

(0.30")

5.0 mm

(0.20")

12.0 mm

(0.47")

15.0 mm

(0.59")

2x ø2.2 mm

(0.09")

2.2 mm

(0.09")

2.3 mm

(0.09")

5.9 mm

(0.23")

7.9 mm

(0.31")

Lens

Indicator for
Light Sensed
(Emitters only)

7.5 mm

(0.30")

15.0 mm

(0.59")

2.3 mm

(0.09")

2.2 mm

(0.09")

12.0 mm

(0.47")

5.9 mm

(0.23")

4.0 mm

(0.15")

5.0 mm

(0.20")

11.7 mm

(0.46")

3.0 mm

(0.12")

Indicator

Lenses

2x ø2.2 mm

(0.09")

SP3ER Models

SP3D1

SP8ER Models

SP8E1 Emitter
(or SP8R2 Receiver)

SP3E1 Emitter
(or SP3R2 Receiver)

SP3R1 Receiver 

(or SP3E2 Emitter)

SP8R1 Receiver 

(or SP8E2 Emitter)

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Содержание PICO-AMP MD14BB6









Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды