Alignment Procedure
To align a safety light screen using the LAT-1:
REMOVE TWO PHILLIPS
SCREWS
FOR BA
TTER
Y ACCESS
BELOW
DO NOT S
TARE
INTO BEAM. CLASS
2 LASER PRODUC
T.
AVOID EXPOSURE
- LASER
LIGHT
EMITTED FROM THIS
APER
TURE
REQUIRES
ONE 9V BA
TTER
Y
LASER LIGHT
LAT - 1
Peak Power
: 2.8 m
W, 660-680n
m
33kHz 25% duty cycl
e
COMPLIES
WITH
21 CFR
PART
1040.10 AND EN60825-1;
199
4
LAT-1
Laser Alignment
Tool
Emitter
Receiver
Retroreflective
Target
Mirror 1
REMOVE TWO PHILLIPS
SCREWS
FOR BA
TTER
Y ACCESS
BELOW
DO NOT S
TARE
INTO BEAM. CLASS
2 LASER PRODUC
T.
AVOID EXPOSURE
- LASER
LIGHT
EMITTED FROM THIS
APER
TURE
REQUIRES
ONE 9V BA
TTER
Y
LASER
LIGHT
LAT - 1
Peak Power
: 2.8
m
W, 660-680n
m
33kHz
25% duty cycl
e
COMPLIES WITH 21 CFR
PART
1040.10 AND EN60825-1; 199
4
Mirror 2
Figure 3. Aligning a corner-mirror light screen application using the Laser Alignment Tool
1. Mount all sensors and corner mirrors per the instructions in the appropriate manual. Leave the hardware slightly loose to allow for
positioning adjustment.
2. Assemble the appropriate clip to the LAT-1; snap it onto the light screen emitter or receiver, and slide it to one end of the sensor.
(HINT: Check the receiver for plumb first, before attaching the LAT-1 to the emitter for alignment.) Attach a retroreflective target to the
corresponding end of the opposite sensor.
3. If the sensors are mounted vertically, check the circular bubble level for plumb orientation.
4. Standing behind the Alignment Tool, view the retroreflective target from behind the sensor (see Figure 2). Adjust either or both sen-
sors and/or the corner mirrors as needed to place the laser image at the desired spot on the opposite sensor.
5. Move the Alignment Tool and the retroreflective target to the opposite ends of the sensors and repeat step 4.
6. Repeat steps 4 and 5 until the image falls at the desired spot at both the top and bottom of the opposite sensor; then tighten all
mounting hardware.
Banner Engineering Corp Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of
shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned
to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse,
abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (IN-
CLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND
WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL
BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPEN-
SES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY
PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WAR-
RANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or
liabilities relating to any product previously manufactured by Banner Engineering Corp.
LAT-1-x Laser Alignment Tool
