manualshive.com logo in svg

Banner E-Stop ES-TN-14H5, Инструкция по эксплуатации

Поделиться
Скачать
Banner E-Stop ES-TN-14H5 Скачать руководство пользователя страница 1

E-Stop Safety Modules with Adjustable Delay

®

Models 

ES-TN-14H5

 with 0-20 second delay, 

ES-TN-14H6

 with 0-200 second delay

Features

•   Selectable Auto-Reset or monitored Manual Reset.

•  Auto or manual power-up

•  One- or two-channel feedback monitoring

•   Monitors one dual-channel or one single-channel normally closed E-stop switch 

circuit for a contact failure or wiring fault (safety category 2 or 4,  

per ISO13849-1 [EN954-1]; see pages 5-7).

•  4 amp safety output contacts

•  Removable terminal blocks

•   Input monitoring circuit has diverse-redundant microprocessors

•   Designed for use in functional stop Category 0 and 1 applications (per ISO/EN 

60204-1 and NFPA79)

•   Four immediate output switching channels (functional stop Category 0) and four 

delayed output switching channels (functional stop Category 1). Delay time is 

adjustable from 0-20 seconds or 0-200 seconds, depending on model. 

•   One auxiliary non-safety, normally closed immediate output and one auxiliary 

non-safety normally closed delayed output for status monitoring.

WARNING . . .

  

This Emergency Stop 

Safety Module is not 

a point-of-operation 

guarding device, as 

defined by OSHA regulations.

 It 

is necessary to install point-of-

operation guarding devices, such 

as safety light screens and/or hard 

guards, to protect personnel from 

hazardous machinery. 

Failure to 

install point-of-operation guards 

on hazardous machinery can 

result in a dangerous condition 

which could lead to serious 

injury or death.

!

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Содержание E-Stop ES-TN-14H5

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды