Indicators
Figure 3. Indicators—Back and Top of Device
3
4
5
6
7
1
2
Indicator
Color
Description
1 Power
Blue
Indicates that the reader is connected to the power supply
2 Ethernet Connection
Amber
Indicates connection to the Ethernet network
3 STATUS
Red
No read result
4 COM/Test
Amber
Active result output transmission on the Main serial port
5 TRIGGER/Aim
Amber
Reading in progress. Do not trigger a new reading attempt un-
til the current attempt finishes
6 GOOD/Setup
Green
Reading successful
7 READY/Learn
Green
Ready
During the reader startup, all of the LEDs turn on for one second.
See for the colors and meanings of the five LEDs when the reader is in Smart Teach mode.
Laser Description and Safety Information
The ABR 7000 internal illuminators contain two aiming Laser LEDs used to position the reader. Disconnect the power supply when opening the
device during maintenance or installation to avoid exposure to hazardous laser light. The laser beam can be switched on or off through a soft-
ware command.
This product conforms to the applicable requirements of IEC 60825-1 and complies with 21 CFR 1040.10 except for deviations pursuant to La-
ser Notice N° 50, date June 24, 2007. This product is classified as a Class 2 laser product according to IEC 60825-1 regulations.
CAUTION:
Use of controls or adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure. Do not attempt to disassemble this sensor for repair. A defective unit must be returned to
the manufacturer.
For Safe Laser Use - Class 2 Lasers
•
Do not stare at the laser.
•
Do not point the laser at a person’s eye.
•
Mount open laser beam paths either above or below eye level, where practical.
•
Terminate the beam emitted by the laser product at the end of its useful path.
Reference IEC 60825-1:2007, Section 8.2.
CAUTION:
•
Never stare directly into the sensor lens.
•
Laser light can damage your eyes.
•
Avoid placing any mirror-like object in the beam. Never use a
mirror as a retroreflective target.
Class 2 Lasers
Class 2 lasers are lasers that emit visible radiation in the wavelength range from 400 nm to
700 nm, where eye protection is normally afforded by aversion responses, including the blink
reflex. This reaction may be expected to provide adequate protection under reasonably fore-
seeable conditions of operation, including the use of optical instruments for intrabeam viewing.
Class 2 Laser Safety Notes
Low-power lasers are, by definition, incapable of causing eye injury within the duration of a
blink (aversion response) of 0.25 seconds. They also must emit only visible wavelengths (400
to 700 nm). Therefore, an ocular hazard may exist only if individuals overcome their natural
aversion to bright light and stare directly into the laser beam.
R
C
US
Complies with 21 CFR 1040. 10
except for deviations pursuant
to Laser Notice N°50.
date June 24, 2007
LASER LIGHT - DO NOT ST ARE INTO BEAM
CLAS S 2 LASER PRODUCT
MAX .OUTPUT RADIA TION 1 mW
EMIT TED W AVE LENG TH 630 ~ 680 nm
IEC 60825-1: 2007
www.bannerengineering.com
ABR Series
AVOID EXPOSURE LASER LIGHT
IS EMITTED FROM THIS APERTURE
Laser wavelength:
630-680 nm
Output:
1 mW
Pulse Duration:
variable
Installation Instructions
Mount the Reader
Note:
Mount the device at a 10° to 15° angle from the target to avoid direct reflections.
1. Rotate the connector block to the desired angle.
Figure 4. Connector Block
Connector block
rotates to 90˚ position
ABR 7000
2
P/N 207633 Rev. D
