manualshive.com logo in svg

banks Derringer 66571, Руководство по установке, Страница: 13 / 28

Поделиться
Скачать
banks Derringer 66571 Скачать руководство пользователя страница 13

97282 v.3.0   

13

9.

 Connect the male ends of both the 

FRP and TMAP Derringer harness to 

the sensors on-engine. Pay specific 

attention to the connector latch 

orientation and engagement, making 

sure that the connector fully engages 

the sensor and latches in place. Check 

each connection by pulling firmly on 

the connector body after latching - 

note that the male Derringer harness 

connectors do not use a sliding 

connector lock, only a latch.

 Pay specific 

attention to the orientation of 

Female TMAP connector in the 

following step. Damage can result 

with improper connection. Wedge 

lock on female TMAP connector 

(Derringer Harness) must be 

oriented on same side as connector 

locking latch and yellow lock (OEM 

Engine Harness).

10. 

Connect the female ends of both 

the FRP and TMAP Derringer harness 

to the factory harness, again making 

sure that the connector bodies are 

oriented properly and latch securely 

when connected. Slide the factory 

harness connector locks into place, 

and confirm that the connections are 

secure by tugging firmly on either 

side of the junction. Secure the 

harness connectors to the engine with 

supplied zipties.

11.

  

 

EGT Harness Install 

– This enables “Full Power Extension” 

mode in Derringer. This is optional 

and not required to achieve increased 

power levels.  Connecting this harness 

extends the duration of maximum 

power by 10 seconds. If EGT intercept 

is not used, connect the male and 

female connectors of the Derringer 

harness, and zip tie the branch in a 

safe location. See 

Figure 9

Figure 9

Ram 1500 – EGT intercept 

From underneath the vehicle, locate 

the Exhaust Gas Temperature (EGT) 

connector located on the passenger’s 

side of the transmission. See 

Figure 8.

 

Route the EGT branch of the Derringer 

harness down behind the engine on 

the passenger’s side to this connector 

location. Disconnect the factory EGT 

connection. Note: It may be easier 

to disconnect this connection if 

the connector is removed from its 

mounting tab.

Figure 8

OPTIONAL

Passenger side underneath

Front of truck

If not used

Ram 1500

Transmission

Содержание Derringer 66571





























Отзывы:

Нет отзывов