manualshive.com logo in svg
background image

The European Parliament and the 

Council of the European Union 
have issued the Waste Electrical 
and Electronic Equipment Directive. 

The purpose of the Directive is the 

prevention of waste of electrical 
and electronic equipment, and to 
promote the reuse and recycling 
and other forms of recovery of 
such waste. As such the Directive 
concerns producers, distributors 
and consumers. 

The WEEE directive requires that 

both manufacturers and end-
consumers dispose of electrical 
and electronic equipment and 
parts in an environmentally safe 
manner, and that equipment and 
waste are reused or recovered for 

their materials or energy. 
Electrical and electronic equipment 
and parts must not be disposed of 
with ordinary household refuse; all 

electrical and electronic equipment 
and parts must be collected and 
disposed of separately. 

Products and equipment which 
must be collected for reuse, 
recycling and other forms of 
recovery are marked with the 
pictogram shown. 
When disposing of electrical and 
electronic equipment by use of the 
collection systems available in your 
country, you protect the 
environment, human health and 
contribute to the prudent and 
rational use of natural resources. 
Collecting electrical and electronic 
equipment and waste prevents the 
potential contamination of nature 
with the hazardous substances 
which may be present in electrical 
and electronic products and 
equipment. 

Your Bang & Olufsen retailer will 

assist with and advise you of the 
correct way of disposal in your 
country. 

Waste Electrical and Electronic Equipment (WEEE) – 
Environmental protection 

18

Содержание BeoLink Wireless 1





















Отзывы: