background image

For the Canadian market only! 

This class B digital apparatus meets 

all requirements of the Canadian 
Interference-Causing Equipment 
Regulations. 

This product fulfils the 

conditions stated in the 

EEU directives 89/336 and 73/23. 

Technical specifications, features 

and the use thereof are subject to 
change without notice! 

For the US-market only! 

NOTE: This equipment has been 

tested and found to comply with 
the limits for a class B digital device, 

pursuant to part 15 of the FCC Rules. 

These limits are designed to provide 

reasonable protection against harm-
ful interference in a residential 

installation. 

This equipment generates, uses and 

can radiate radio frequency energy 
and, if not installed and used in 

accordance with the instructions, 

may cause harmful interference to 
radio communications. However, 

there is no guarantee that inter-
ference will not occur in a particular 

installation. If this equipment does 
cause harmful interference to radio 
or television reception, which can be 
determined by turning the equip-
ment off and on, the user is 

encouraged to try to correct the 
interference by one or more of the 
following measures: 

–  Reorient or relocate the receiving 

antenna. 

–  Increase the separation between 

the equipment and receiver. 

–  Connect the equipment into an 

outlet on a circuit different from 

that to which the receiver is 

connected. 

–  Consult the retailer or an 

experienced radio/TV technician 
for help. 

3509114

  

0508

 

Printed in Denmark by Bogtrykkergården a-s, Struer 

Содержание BeoLab 7-1













Отзывы: