Bandit INTIMIDATOR 19XPC Скачать руководство пользователя

Страница: 48 / 167

Bandit

MODEL 19XPC

CONTROLS

DINAMIC WINCH OPERATING PROCEDURES

Handle to free

spool with

manual controls

Winch Control

with Feed Assist

Winch line

shown cradled

through the

winch line

docking ass’y

hanger

Winch Hook

Mount

Winch

Valve

Feed

Assist

Valve

Manual Controls

Winch Control Panel

OPERATE HYDRAULIC WINCH PER INSTRUCTIONS!

Install the line to pull and feed from the bottom of the winch drum.

WARNING

DANGER

Never reach into the winch, fairlead, or winch roller area.

1. Winch operation is a one person job. This means

the person who hooks the winch line to the wood

material is the same person who engages the winch.

Place the feedwheel control bar in the off position.

The chipper and towing vehicle must be blocked or

anchored in a solid location.

3. Locate the handle on the winch unit and position

it to the free spool mode by pulling the handle to

the side then down to the bottom position. If the

machine has a winch control panel on the side

of the infeed hopper, position the toggle switch to

the winch free spool position; the winch free spool

indicator light should be on. While the winch is

in normal operation or free spool mode the feed

system will not work.

4. Pull the winch line to the material to be pulled.

Attach the winch line securely to the wood

material that you want pulled to the chipper.

5. Engage the winch by moving the handle to the

side then up to the top position. If the machine

has the winch control panel, position the switch

in the winch engaged position.

6. Make sure everyone is clear. Use the winch

control valve or the radio remote control (if

applicable) to now pull the wood material towards

the machine. Check that the controls operate in

the correct direction.

OPERATING PROCEDURE

7. If the machine has the optional feed assist,

once the wood material is pulled to the machine,

the optional feed assist can be pushed to

momentarily operate the feed system with the

feed control bar in the feed position to get the

wood staged into the feedwheels. If the machine

has the winch control panel, the winch control

can momentarily be put in the slow feed mode

to momentarily operate the feed system with the

feed control bar in the feed position to get the

wood staged into the feedwheels. With either

winch system, re-hook the winch line as needed

before starting the wood into the feedwheels.

Make sure the feed control bar is in the off position.

9. Unhook the winch line from the wood material

and attach the end of the winch line end to the

winch hook mount.

10. Start reeling the winch line in.

11. Once the winch line gets close to being reeled

in all the way, cradle the winch line in the winch

line docking assembly hanger.

12. When the winch line is reeled in all the way,

the winch line docking system will be activated

and once the feed control bar is positioned in the

feed position the feedwheels will begin feeding

wood material.

Содержание INTIMIDATOR 19XPC








































































































































































Результаты поиска

Содержание INTIMIDATOR 19XPC

Отзывы:

Похожие инструкции для INTIMIDATOR 19XPC

Бренды по названию

Популярные бренды

Bandit INTIMIDATOR 19XPC, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание INTIMIDATOR 19XPC

Отзывы:

Похожие инструкции для INTIMIDATOR 19XPC

Бренды по названию

Популярные бренды