background image

RF Emissions notice

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environ-

ment. This device’s antenna must be installed in accordance with provided instructions; and it must 

be operated with minimum 96 cm spacing between the antennas and all person’s body (excluding 

extremities of hands, wrist and feet) during operation. Further, this transmitter must not be co-located 

or operated in conjunction with any other antenna or transmitter.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condi-

tions: (1) this device may not cause harmful interference, and (2) this device must accept any inter-

ference received, including interference that may cause undesired operation.

Note:

 This equipment has been tested and found to comply with the limits for a Class B digital device, 

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 

harmful interference in a normal installation. This equipment generates, uses and can radiate radio 

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 

interference to radio communications. However, there is no guarantee that interference will not occur 

in a particular installation. If this equipment does cause harmful interference to radio or television 

reception, which can be determined by turning the equipment off and on, the user is encouraged to 

try to correct the interference by one or more of the following measures:

  Reorient or relocate the receiving antenna.
  Increase the separation between the equipment and receiver.
  Connect the equipment into an output on a circuit different from that to which the receiver is 

connected.

  Consult the dealer or an experienced technician for help.
  A shielded cable must be used when connecting a peripheral to the serial ports.

Notice specific to the H50  

This ISM device complies with Canadian ICES-001.
Maintain a minimum separation of 2.5 cm (1 inch) from the face.
Cet appareil ISM est conforme à la norme NMB-001 du Canada.
Maintenir une distance minimum de 2,5 cm (1 inch) de la surface.

Industry Canada Statement

This device complies with Industry Canada license-exempt RSS standard(s).
Operation is Subject to the following two conditions: (1) this device may not cause interference, 

and (2) this device must accept any interference, including interference that may cause undesired 

operation of the devise.
Le présent appareil est conforme aux CNR d’industrie Canada applicables aux appareils radio  

exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pa produire de 

brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même 

si le brouillage est susceptible d’en compromettre le fonctionnement.

CE Compliance Statement

This product complies with CE under R&TTE directive 1999/5/EC. The relevant Declaration of Con-

formity is available in the following website under model documentation section:  

http://www.bandg.com.

B&G - V50 & H50 Installation Instructions

5

Содержание V50 VHF























Отзывы: