baltur TBG 450LX ME, Инструкция по установке, использованию и обслуживанию

Страница: 50 / 92

SPECIAL PRECAUTIONS WHEN USING GAS.
• Check that the feed line and the train comply with current law and
regulations.
• Check that all the gas connections are properly sealed.
• Do not leave the equipment on when it is not in use and always close
the gas cock.
• If the user is absent for a prolonged period of time, close the main
gas feed tap to the burner.
• If you smell gas:
- do not operate electrical switches, phones or any other object
that may cause sparks;
- open immediately doors and windows to create a draught to
clear the air in the room;
- close the gas cocks;
- have professionally qualifi ed personnel correct the fault.
• Do not obstruct ventilation openings in the room where there is gas
equipment. Otherwise, dangerous situations may arise with the build
up of toxic and explosive mixtures.
• If the user is absent for a prolonged period of time, close the main
gas feed tap to the burner.
RESIDUAL RISKS
• Even though the product was designed in compliance with the obli-
gatory standards, residual risks may still be present during correct
operation. They are signalled on the burner through special Picto-
grams.
CAUTION
Moving mechanical organs.
CAUTION
Materials at high temperature.
CAUTION
Powered electric panel.
ELECTRIC SAFETY WARNINGS
• Check that the equipment has a suitable ground system, carried out
following safety standards in force.
• Have qualifi ed personnel check that the electric system is adequate
to equipment maximum power consumption indicated on the plate.
• Remove the external insulating seal of the supply pipe necessary for
the connection, preventing the cable to touch metal parts.
• The use of any electrically fed components entails complying with
certain fundamental rules, including the following:
- do not touch the equipment with parts of the body that are wet or
damp or with damp feet;
- do not pull on electrical cables;
- do not leave the equipment exposed to atmospheric agents
(such as rain or sun etc.) unless there is explicit provision for
this;
- do not allow the equipment to be used by children or inexpert
persons;
- The power supply cable for the equipment must not be replaced
by the user. In case of cable damage, turn the equipment off. To
replace it contact qualifi ed personnel only;
- If you decide not to use the equipment for a certain period of time
it is advisable to switch off the electrical power supply to all com-
ponents in the system that use electricity (pumps, burner, etc.).
• Use regulation-compliant fl exible cables EN60335-1:EN 60204-1
- in case of PVC sheath, at least type H05VV-F;
- in case of rubber sheath, at least type H05RR-F; LiYCY
450/750V
- without any sheath, at least type FG7 o FROR, FG70H2R
• The electric equipment works correctly at altitudes of up to 1000 m
above the see level.
TO BE CARRIED OUT BY THE INSTALLER
• Install a suitable circuit breaker for each power supply line of the bur-
ner, according to the characteristics and the diagram on the chapter
ELECTRICAL CONNECTIONS.
• The disconnection must be carried out by means of a device com-
plying with the following requirements:
- A disconnecting switch - circuit breaker, according to IEC 60947-
3 for at least the equipment category AC-23 B (non-frequent
operations on highly inductive loads or AC motors).
- A control and protection switching device suitable for isolation
according to IEC 60947-6-2.
- A switch suitable for isolation according to IEC 60947-2.
• The disconnecting device must:
- Ensure the isolation of the electrical equipment from the power
supply line when in the stable OFF position indicated with “0”,
and be in a stable ON position indicated with “1”.
- Feature a visible gap between contacts or a position indicator
that cannot indicate OFF (isolated) until all contacts are actually
open and the requirements for the isolation function are met.
- Feature a grey or black actuator which can be easily identifi ed.
- Be padlockable in the OFF position. In case of lock-out, remote
and local activation will not be possible.
- Disconnect all the active conductors of its power supply circuit.
For TN power supply systems, the neutral conductor can be
disconnected or not, except in the countries where the discon-
nection of the neutral conductor (if used) is mandatory.
• Both disconnecting controls must be located at a height between 0,6
m ÷ 1, 7 m with respect to the working plane.
• Since circuit breakers are not emergency devices, they can feature
an additional cover or a door, which can be easily opened without
any key or tool. Its function must be clearly indicated, e.g. with the
relevant symbols.
• The burner can be installed only in TN or TT systems. It cannot be
installed in isolated system of IT type.
ENGLISH
4 / 44
0006160281_202007