background image

BV225 Amplifier
Installation Instructions

2

BV225 Installation Manual issue 3

Over temperature protection is provided using sensors attached 
to the output stage heat sink. Should the temperature exceed 90 
Degrees Celsius the input signal to the relevant amplifier will be 
attenuated to a safe level and the “Overload” LED will be 
illuminated.

If the system is under surveillance it will cause the surveillance 
detector to indicate a fault condition due to the gain reduction.

1.2  BV225 A

MPLIFIER

 S

PECIFICATIONS

Parameter

Value (Per Amplifier)

Rated output power less than 0.2% THD

225W @ 44.5

Ω

Output regulation 225W @ 44.5

Ω

Better than 1.5dB

Output Voltages obtainable

50V & 100V

Frequency response 225W @ 44.5

Ω

 (-3dB)

35Hz - 20kHz

Input sensitivity and impedance

500mV @ 40K

Ω

 

Input common mode rejection ratio (50Hz - 20kHz)

Better then 40dB, typically 60dB

Output noise reference to rated output

Better than 85dB

Cross talk between amplifiers @ 1kHz

Better than 70dB

Supply Voltage

22V - 35V DC

Supply Current: Sleep mode @ 26V (Battery supply)

50mA

Supply Current: Quiescent @ 30V (Mains supply)

160mA

Supply Current: Rated output power 225W @ 44.5

Ω

10A

Supply DC Fuse (Automotive Style Blade)

15A

Output Stage Protection: Thermal

Output stage above 90°C

Output Stage Protection: Load

Excessive Output Stage Current

Output Stage Protection: Action

Reduces input to a safe level

Front Panel Indicators

Power (Green)

DC Supply Connected

Overload (Yellow)

Protection circuit operating 

100% (Yellow)

100V Output Voltage

10% (Green)

10V Output Voltage

Terminations

Loudspeaker 100V Line Output

2 off 3 way cage clamp

Balanced Line Inputs

2 off RJ45 connectors

DC Supply Input

2 pin crimp connectors

Содержание BV225

















Отзывы: