manualshive.com logo in svg

Balboa TP500, Руководство пользователя, Страница: 19 / 26

Поделиться
Скачать
Balboa TP500 Скачать руководство пользователя страница 19

42339 rev A1

03/06/20

19

Manufactured under one or more of these patents.  U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 

6965815, 7030343, 7,417,834 b2, Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending.   All 

material copyright of Balboa Water Group.

General Messages

R U N

P M P 5

P U R G

A I R

- - - -

W A T R

T O O

H O T

- - - -

T O O

C O L D

Priming Mode – MO19

Each time the spa is powered up, it will enter Priming Mode. The purpose of Priming Mode is to allow the user to run each pump and 

manually verify that the pumps are primed (air is purged) and water is flowing. This typically requires observing the output of each pump 

separately, and is generally not possible in normal operation.  Priming Mode lasts 4 minutes, but you can exit it earlier by pressing any 

Temp button. The heater is not allowed to run during Priming Mode.
NOTE: If your spa has a Circ Pump, it will turn on with “Light” in Priming Mode. The Circ Pump will run by itself when Priming Mode is 

exited. 

Water is too Hot (OHS) – MO29

One of the water temp sensors has detected spa water temp 110°F (43.3°C) and spa functions are disabled.  System will auto reset when 

the spa water temp is below 108°F (42.2°C). Check for extended pump operation or  

high ambient temp.

* This message can be reset from the topside panel with any button press. 

M0XX numbers are Message Codes. See Page 18. 

Too Cold - Freeze Protection

A potential freeze condition has been detected, or the Aux Freeze Switch has closed, and all pumps and blower are activated, either one 

at a time, or all at once, depending on how your system was built. All pumps and blower are ON for at least 4 minutes after the potential 

freeze condition has ended, or when the aux freeze switch opens. 
In some cases, pumps may turn on and off and the heater may operate during Freeze Protection. 
This is an operational message, not an error indication. 

- - - C

Water Temperature is Unknown

After the pump has been running for 1 minute, the temperature will be displayed.

T R I P

J 2 9

- - - -

J29 Warning – MO44

J29 is typically used as a Heater Disable input. As such, it should not typically be shorted at power-up. This message appears if J29 is 

shorted at power-up.

Содержание TP500



























Отзывы:

Нет отзывов