28
RE-ASSIGNING DEVICE KEYS
The Dolphin can be set up to control a second TV
or VCR, or any combination of four home
entertainment components. For example, to have
the Dolphin control a TV, a Cable Converter, and
two VCRs, you will need to re-assign the unused
AUDIO key to operate the second VCR as follows:
1. On the Dolphin, press and hold SETUP until the
LED blinks twice, then release SETUP.
2. Enter 9 - 9 - 2.The LED will blink twice.
3. Press VCR once, then press AUDIO once.
4. The AUDIO key is now ready to be
programmed for your second VCR. See
Programming VCR Control on page 12.
To re-assign other device keys, repeat steps 1
through 4 by substituting the key sequence from
the following chart for a desired component:
To Re-Assign
Perform Key Sequence
TV as 2nd VCR key:
SETUP - 9 - 9 - 2 - VCR - TV
TV as 2nd Audio key:
SETUP - 9 - 9 - 2 - AUDIO - TV
TV as 2nd Cable key:
SETUP - 9 - 9 - 2 - CBL - TV
TV back to TV
SETUP - 9 - 9 - 2 - TV - TV
VCR as 2nd TV key:
SETUP - 9 - 9 - 2 - TV - VCR
VCR as 2nd Audio key:
SETUP - 9 - 9 - 2 - AUDIO - VCR
VCR as 2nd Cable key:
SETUP - 9 - 9 - 2 - CBL - VCR
VCR back to VCR:
SETUP - 9 - 9 - 2 - VCR - VCR
AUDIO as 2nd TV key:
SETUP - 9 - 9 - 2 - TV - AUDIO
AUDIO as 2nd VCR key:
SETUP - 9 - 9 - 2 - VCR - AUDIO
AUDIO as 2nd Cable key: SETUP - 9 - 9 - 2 - CBL - AUDIO
AUDIO back to AUDIO:
SETUP - 9 - 9 - 2 - AUDIO - AUDIO
Upon completion of a re-assignment, the LED will
blink twice to confirm your selection.At that time,
you will also need to program the Dolphin to
control the new component (see previous sections
on Programming TV Control, Programming VCR
Control, Programming Cable Control, or
Programming Audio Control).
29
CHANGING VOLUME LOCK
The Dolphin is set to control volume of a
component through your TV while in the TV,VCR,
or Cable mode. However, in the Audio mode, you
have separate control of of your audio
component’s volume.
If your TV is not remote controllable, or if you
would like the volume to be controlled by a
different component, you can change the Volume
Lock setting to control a volume through a non-
associated mode (e.g., through the cable in the TV
mode).
To change Volume Lock to the CABLE mode:
1. On the Dolphin, press and hold SETUP until the
LED blinks twice, then release SETUP.
2. Enter 9 - 9 - 3 and then press CBL once.The
LED will blink twice.
3. Now,whenever you press , Volume –,
or MUTE on the Dolphin, volume will be
controlled by your Cable Converter.
To change Volume Lock to the TV mode:
1. On the Dolphin, press and hold SETUP until the
LED blinks twice, then release SETUP.
2. Enter 9 - 9 - 3 and then press TV once. The
LED will blink twice.
3. Now,whenever you press , Volume –,
or MUTE on the Dolphin, volume will be
controlled by your TV.
To change Volume Lock to the VCR mode:
1. On the Dolphin, press and hold SETUP until the
LED blinks twice, then release SETUP.
2. Enter 9 - 9 - 3 and then press VCR once. The
LED will blink twice.
3. Now,whenever you press , Volume –,
or MUTE on the Dolphin, volume will be
controlled by your VCR.
To change Volume Lock to the RCVR mode:
NOTE: Performing these steps will allow you to
access the volume control of your audio
component in all modes.
1. On the Dolphin, press and hold SETUP until the
LED blinks twice, then release SETUP.
2. Enter 9 - 9 - 3 and then press AUDIO once. The
LED will blink twice.
3. Now,whenever you press , Volume –,
or MUTE on the Dolphin, volume will be
controlled by your audio component.