background image

3

7.  Pivot the footbar slightly until the large hole at the bottom 

of the footbar aligns with the remaining hole in the trunnion 
plate. 

8.  Slide the shoulder bolt with one washer through the large 

footbar hole. Then screw the shoulder bolt into the trunnion 
plate as tightly as possible with the large allen wrench. Repeat 
on the other side. See Figure E.

INSTALL THE RISERS

9.  Remove locking pins from the 

frame. Insert the risers 
through the holes on the top 
of the frame. Turn the risers 
until the attached pulleys point 
straight down the frame toward 
the footbar. See Figure F. 

10. Reinsert locking pins until the 

metal ring touches the frame. 
You may need to jiggle or 
slightly lift or rotate the riser 
to get the locking pins in all 
the way. 

ATTACH THE ROPES

11.  To attach the ropes, first engage at least one spring from 

the carriage to the frame to keep the carriage in the home 
position. Unroll the ropes and separate them.

12. The Allegro CC now comes with Soft Touch Ropes that do not 

have the dog-clips to attach the loops. The clip will no longer 
drag on or bang into the frame! Follow the images below to 
install your loops. See Figure G. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

13. Rest the loops over the shoulder rests. Thread the other end of 

each rope through a riser pulley and back into the cam cleats 
on the carriage to adjust the length. Be sure to go through the 
chrome eyestraps on both sides of the cam cleats. Always push 
the rope firmly down into the cleats to ensure a good grip.

STORING THE ALLEGRO CC REFORMER

Stacking

To see a demonstration of how to stack the Allegro CC, watch the 
Setup and Safety portion of the Allegro CC Introductory/Level 1 
DVD. Attach the springs to keep the carriage from moving. Move 
the footbar to the “down” position. Remove the shoulder rests 
and store in the slots at the head of the frame. Put the head rest 
down. Remove the risers and store in the holes on the sides of 
the frame. Place the ropes and loops inside the Allegro CC frame 
not on the carriage. Alternate the orientation of the Allegro CC‘s 
as you stack them. Place the head end feet onto the standing 
platform of the Allegro CC below, and so on. Stack a maximum 
of 5 reformers with no legs (3 with legs). Do not stack Reformer 
with Towers.

Standing 

It is absolutely critical that the 
Allegro CC footbar be set and 
locked in the correct position 
for standing storage. Move 
and lock the footbar into the 
position closest to the foot-end 
of the Reformer frame. Raise 
the footbar to its highest 
position. Lift the head-end of 
the Allegro CC frame to waist 
height. Then raise the frame to 
vertical. Use your foot to steady 
the wheeled end of the frame 
as you lift to vertical. The 
vertical Allegro CC will come 
to rest on the footbar and the 
transport wheels. 
See Figure H.

Figure F

Locking Pin

Figure G

2

1

3

4

Figure H

Содержание Allegro CC







Отзывы: