background image

© 2018 Baker Hughes, a GE company. All Rights Reserved. 

Masoneilan Regulators Models 525 & 526 Manual | b 

THESE INSTRUCTIONS PROVIDE THE CUSTOMER/OPERATOR WITH IMPORTANT PROJECT-SPECIFIC  REFERENCE 
INFORMATION IN ADDITION TO THE CUSTOMER/OPERATOR’S NORMAL OPERATION AND MAINTENANCE 
PROCEDURES. SINCE OPERATION AND MAINTENANCE PHILOSOPHIES VARY, BHGE (BAKER HUGHES, A GE COMPANY 
AND ITS SUBSIDIARIES AND AFFILIATES) DOES NOT ATTEMPT TO DICTATE SPECIFIC PROCEDURES, BUT TO PROVIDE 
BASIC LIMITATIONS AND REQUIREMENTS CREATED BY THE TYPE OF EQUIPMENT PROVIDED.  

THESE INSTRUCTIONS ASSUME THAT OPERATORS  ALREADY HAVE A GENERAL UNDERSTANDING OF THE 
REQUIREMENTS FOR SAFE OPERATION OF MECHANICAL AND ELECTRICAL EQUIPMENT IN POTENTIALLY HAZARDOUS 
ENVIRONMENTS. THEREFORE, THESE INSTRUCTIONS SHOULD BE INTERPRETED AND APPLIED IN  CONJUNCTION 
WITH THE SAFETY RULES AND REGULATIONS APPLICABLE AT THE SITE AND THE PARTICULAR REQUIREMENTS FOR 
OPERATION OF OTHER EQUIPMENT AT THE SITE. 

THESE INSTRUCTIONS DO NOT PURPORT TO COVER ALL DETAILS OR VARIATIONS IN EQUIPMENT NOR TO PROVIDE 
FOR EVERY POSSIBLE CONTINGENCY TO BE MET  IN CONNECTION WITH INSTALLATION, OPERATION  OR 
MAINTENANCE. SHOULD FURTHER INFORMATION BE DESIRED OR SHOULD  PARTICULAR PROBLEMS  ARISE WHICH 
ARE NOT COVERED SUFFICIENTLY FOR THE CUSTOMER/OPERATOR'S PURPOSES THE MATTER SHOULD BE REFERRED 
TO BHGE.  

THE RIGHTS, OBLIGATIONS AND LIABILITIES OF BHGE AND THE CUSTOMER/OPERATOR ARE STRICTLY LIMITED TO 
THOSE EXPRESSLY PROVIDED IN THE CONTRACT  RELATING TO THE SUPPLY OF THE EQUIPMENT. NO ADDITIONAL 
REPRESENTATIONS OR WARRANTIES BY BHGE REGARDING THE EQUIPMENT OR ITS USE ARE GIVEN OR IMPLIED BY 
THE ISSUE OF THESE INSTRUCTIONS. 

THESE INSTRUCTIONS ARE FURNISHED TO THE CUSTOMER/OPERATOR SOLELY TO ASSIST IN THE INSTALLATION, 
TESTING, OPERATION, AND/OR MAINTENANCE OF THE EQUIPMENT DESCRIBED. THIS DOCUMENT  SHALL NOT BE 
REPRODUCED IN WHOLE OR IN PART WITHOUT THE WRITTEN APPROVAL OF BHGE. 

 

 

Содержание Masoneilan 525
















Отзывы: