Baker Hughes Masoneilan 51 Series Скачать руководство пользователя страница 34

Страница: 34 / 40

34 |

Baker Hughes

13. Replace Cylinder Tube (14) and Separator Plate (13). Coat the inner surface of the Cylinder Tube with silicone

grease.

14. Replace spring unit, Spring Tube (7), and Top Plate (17). Coat the sliding surface of the Piston Rod with silicone

grease (or equivalent).

15. Ensure the positions of the air connections are correct. Insert the Center Bolts into the holes of the Top Plate

and Yoke. Mount the Spring Washers and Nuts and tighten them lightly by hand. Mount the Spring Washers and

Nuts to the bottom side of the Yoke by hand. Ensure that the position of Center Bolts (Approxi25 mm

longer than others) for the accessory mounting plate, if equipped, complies with Figure 18.

16. Align the holes of the Top Plate with the Yoke so that the Center Bolts are set vertically.
17. Ensure balanced tightening of the center bolt by tightening the nuts in diagonal pairs gradually to a torque

70.0 ± 5 N-m (52.0 ± 4 ft-lbs).

Figure 18 - Center Bolt Positioning

Ensure that guide bushing inner surface (8) is not scratched by compression nut (12).

Содержание Masoneilan 51 Series





































Результаты поиска

Содержание Masoneilan 51 Series

Отзывы:

Бренды по названию

Популярные бренды

Baker Hughes Masoneilan 51 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Masoneilan 51 Series

Отзывы:

Бренды по названию

Популярные бренды